Abstract:For silicon solar cells, polysilicon‐based passivating contacts exhibit excellent gettering effects during high‐temperature fabrication process. This study confirms that both n‐ and p‐type polysilicon passivating contacts show stable and robust performance to iron gettering. However, iron gettering to the front p‐type emitter is found to degrade the emitter saturation current. The polysilicon‐based solar cells with significant initial bulk iron contamination exhibit lower Voc and Jsc values, interestingly, as well as an increased ideality factor and worse temperature coefficient in Voc. Over the past decade, silicon solar cells with carrier‐selective passivating contacts based on polysilicon capping an ultra‐thin silicon oxide (commonly known as TOPCon or POLO) have demonstrated promising efficiency potentials and are regarded as an evolutionary upgrade to the PERC (passivated emitter and rear contact) cells in manufacturing. The polysilicon‐based passivating contacts also exhibit excellent gettering effects that relax the wafer and cleanroom requirements to some extent. In this work, we experimentally explore the impact of bulk iron contamination and polysilicon gettering on the passivation quality of the polysilicon/oxide structure and the resulting solar cells performance. Results show that both n‐ and p‐type polysilicon/oxide passivating contacts are not affected by iron gettering, demonstrating robust and stable passivation quality. However, for a very high bulk iron contamination (1 × 1013 cm−3), the accumulated iron in the p‐type lightly boron‐doped emitter in crystalline silicon would degrade the emitter saturation current density. This can cause a reduction in both open‐circuit voltage and short‐circuit current. Meanwhile, this very high iron content (1 × 1013 cm−3) can further degrade the fill factor and temperature coefficient of the cells. On the other hand, for an initial iron content of 2 × 1012 cm−3, which should be well above the iron level in the current industrial Czochralski silicon wafers, the resulting cells demonstrate similar performance as the control group with no intentional iron contamination. This work brings attention to both the benefits of polysilicon gettering effects as well as the potential degradation due to the accumulation of metal impurities in the p‐type emitter region.

Influence of Silicon Substrate Surface Finish on the Screen‐Printed Silver Metallization of Polysilicon‐Based Passivating Contacts

Influence of Polysilicon Thickness on Properties of Screen‐Printed Silver Paste Metallized Silicon Oxide/Polysilicon Passivated Contacts

Progress in screen-printed metallization of industrial solar cells with SiOx/poly-Si passivating contacts

Polysilicon Passivating Contacts for Silicon Solar Cells: Interface Passivation and Carrier Transport Mechanism

Effect of Surface Texture on Pinhole Formation in SiO x-Based Passivated Contacts for High-Performance Silicon Solar Cells

Poly-Si passivating contacts prepared via phosphorus spin-on-doping: A comparison between different silicon deposition methods

Current status and challenges for hole-selective poly-silicon based passivating contacts

Role of polysilicon in poly-Si/SiOx passivating contacts for high-efficiency silicon solar cells

Interface Modeling Between the Printed Thick-Film Silver Paste and Emitter for Crystalline Silicon Solar Cells

In Situ Reflectometry and Diffraction Investigation of the Multiscale Structure of p-Type Polysilicon Passivating Contacts for c-Si Solar Cells

Study on the Front Contact Mechanism of Screen-Printed Multi-Crystalline Silicon Solar Cells

Enhancement of Electrical Properties of Nanostructured Polysilicon Layers Through Hydrogen Passivation

Effects on Metallization of n+-Poly-Si Layer for N-Type Tunnel Oxide Passivated Contact Solar Cells

Laser Ablation and Ni/Cu Plating Approach for Tunnel Oxide Passivated Contacts Solar Cells with Variate Polysilicon Layer Thickness: Gains and Possibilities in Comparison to Screen Printing

INFLUENCE OF SILVER PASTE COMPOSITION ON OF SCREEN-PRINTED OHMIC CONTACTS SILICON SOLAR CELLS

Effect of Iron Contamination and Polysilicon Gettering on the Performance of Polysilicon‐Based Passivating Contact Solar Cells

Design Rule of Electron- and Hole-Selective Contacts for Polycrystalline Silicon-Based Passivating Contact Solar Cells

Application of Phosphorus‐Doped Polysilicon‐Based Full‐Area Passivating Contact on the Front Textured Surface of P‐type Silicon

Impurity Gettering by Boron‐ and Phosphorus‐Doped Polysilicon Passivating Contacts for High‐Efficiency Multicrystalline Silicon Solar Cells

Novel polysilicon in resisting thermal-evaporation Al-electrode damage and its application in back-junction passivated contact p-type solar cells

Long-term stability study of the passivation quality of polysilicon-based passivation layers for silicon solar cells