Abstract:Inorganic chloroaluminate molten salts are of interest as electrolytes for the high-rate plating of aluminum because of their high conductivity and low cost. Unfortunately, low-melting Lewis acidic inorganic chloroaluminate molten salts such as AlCl3-rich AlCl3-NaCl are problematic because of the loss of volatile AlCl3, which restricts their use to sealed systems. Most common Lewis neutral chloroaluminate salts that are based on a single alkali chloride salt, e.g., equimolar AlCl3-NaCl or NaAlCl4, are problematic as well because of their high melting points. However, Hjuler et al.1 described a complex mixture of inorganic haloaluminate salts, LiAlCl4-NaAlCl4-NaAlBr4-KAlCl4 (3:2:3:2) [or LiAlBr4-NaAlCl4-KAlCl4 (3:5:2)] with a melting point of only 86 oC. This Lewis neutral salt was originally formulated for use as an electrolyte for rechargeable Al/molten salt/Ni3S2batteries. The facile electrodeposition of aluminum from this salt was also demonstrated. Any electrolyte solution that is used for the continuous electrodeposition or plating of aluminum normally requires an aluminum anode to resupply the aluminum species that is reduced at the cathode and lost from the solution during the plating process. Much research has been directed at the mechanism of the plating reaction at the cathode in haloaluminate melts, but little attention has been directed to the reactions taking place at the anode. As described in a now classical paper by Holleck and Giner,2passivation phenomena at the aluminum anode may ultimately limit the rate of the plating process in these molten salts as well as their use as battery electrolytes. In this presentation, we describe the behavior of the aluminum anode in the LiAlCl4-NaAlCl4-NaAlBr4-KAlCl4 molten salt at 130 oC. The anodization of Al in this melt is a complex process. Figure 1 shows current - time plots recorded at an Al rotating disk electrode at different applied potentials, E app, versus the equilibrium potential, E eq. (0 V versus Al). As shown in the Levich plots in Fig. 2, for E appup to 0.60 V, the anodization of Al is a mass transport-limited process according to the well-known reversible reaction: Al + 7AlX4 - ↔ 4Al2X7 - + 3e- (1) where X = Cl + Br. However, as E app is increased above this value, the current decreases significantly over a short time period, indicating that the amount of AlX4 - supplied by mass transport is not sufficient to support the reaction in Eq. 1. This results in passivation of the Al anode with AlX3(s) according to the reaction Al + 3AlX4 - ↔ 4AlX3(s) + 3e- (2) Once the Al electrode develops a passive layer, the current reaches a steady-state value determined by the rate of AlX3(s) formation (Eq. 2) and dissolution according to the reaction AlX3(s) + AlX4 - ↔ Al2X7 - (3) The Levich plot in Figure 2 suggests that this dissolution process is also mass transport limited. References 1H. A. Hjuler, S. von Winbush, R. W. Berg, and N. J. Bjerrum, J. Electrochem. Soc., 136, 901-906 (1989). 2G. L. Holleck and J. Giner, J. Electrochem. Soc., 119, 1161-1166 (1972). Acknowledgement This work was funded by the Strategic Environmental Research and Development Program (SERDP) through contract DE-AC05-00OR22725 to Oak Ridge National Laboratory with subcontract to the University of Mississippi.

Comparative study of the potentiodynamic behaviour of aluminium at low potentials in barrier layer and in pore-forming electrolytes

The Corrosion and Electrochemical Behaviour of Pure Aluminium in Alkaline Methanol Solutions

Anodic Layer Growth on 1050 and 2024 Aluminium Alloys in Presence of Etidronic Acid : Changes in Morphology and Structure

Establishment of electrode potential-composition plot of Al-Mg-Zn alloys and sacrificial anode protection tests

Revisiting the Anodic Stability of Aluminum Current Collectors in High-Voltage Li-Ion Batteries

Effects of Solid-Solute Magnesium and Stannate Ion on the Electrochemical Characteristics of a High-Performance Aluminum Anode/electrolyte System

Studies On The Anodic Behavior Of Aluminum Electrodes In Alkaline-Solution

Electrochemical Investigation of Li–Al Anodes in Oligo(ethylene Glycol) Dimethyl Ether/lipf 6

Various Modifications of Electrochemical Barrier Layer Thinning of Anodic Aluminum Oxide

Corrosion Inhibition of Aluminum Alloy in 50% Ethylene Glycol Solution

Anode behavior of aluminum alloy AB1 with magnesium

Aluminum Anodization in the Low-Melting LiAlBr4-NaAlCl4-KAlCl4 Molten Salt

Passivation and pH-Induced Precipitation during Anodic Polarization of Steel in Aluminate Electrolytes as a Precondition for Plasma Electrolytic Oxidation

Corrosion and Anodic Behaviors of Pure Aluminum in a Novel Alkaline Electrolyte

An Electrochemical Investigation on the Dissolution of Bilayered Porous Anodic Alumina

Revisiting the Corrosion of the Aluminum Current Collector in Lithium-Ion Batteries

Corrosion Study of Current Collectors for Magnesium Batteries

Nanocontrolled thinning of the barrier layer thickness of porous anodic films using galvanodynamic polarization of aluminum alloys

Investigation of the Anodic Behavior of Al Current Collector in Room Temperature Ionic Liquid Electrolytes

The role of the oxide layer in the corrosion of aluminium in acidic solutions

SVET and ToF-SIMS Studies on the Galvanic Corrosion of Β-Phase/aluminum Couple in Aqueous Solutions As a Function of Ph