Abstract:Aluminum (Al) alloys are the most commonly used non-ferrous metals (approximately 25 million tons per year) for various technical applications and is the second most commonly used metal alloy after steel. Al alloys are also used in combination with other metals or materials to get specific desirable properties for applications such as transportation, construction, electrical appliances, and consumer goods. However, a system of dissimilar materials can lead to potential corrosion problems such as galvanic and crevice corrosion. In this work, atmospheric galvanic corrosion of Al alloy was predicted by combining electrochemical techniques and accelerated laboratory corrosion tests. Three different galvanic couples were analyzed where 6061-T6 Al alloy was coupled with a passivating metal (304 stainless steel), noble metal (copper), and a carbon fiber-reinforced polymer matrix composite (CFR PMC). The galvanic current flowing between the anode and cathode was measured using the zero-resistance ammeter (ZRA) technique in the humidity-chamber setup, cyclic corrosion test chamber following a modified GM9540P cycle, and an outdoor exposure test site. Electrolytes with varying amounts of chloride contents were used to simulate different atmospheric conditions. Four separate equations based on Faraday's law were developed to calculate the corrosion rate in grams per meter square per day (gmd) by relating the time of wetness (TOW) to the galvanic current measured from the accelerated laboratory experiments. The total exposure time was divided into wet periods (Twet) and dry periods (Tdry). The surface morphology of Al samples from the galvanic couples was studied using a scanning electron microscope (SEM), and elemental surface analysis was conducted using energy-dispersive X-ray Spectroscopy (EDXA). Figure 1

SVET and ToF-SIMS Studies on the Galvanic Corrosion of Β-Phase/aluminum Couple in Aqueous Solutions As a Function of Ph

Understanding the Galvanic Corrosion of the Q-phase/Al Couple Using SVET and SIET

SVET Study of Galvanic Corrosion of Al/Mg2Si Couple in Aqueous Solutions at Different Ph

SVET and SIET Study of Galvanic Corrosion of Al/MgZn2in Aqueous Solutions at Different Ph

Simulating Corrosion of Al2cumg Phase by Measuring Ionic Currents, Chloride Concentration and Ph

Electrochemical, TOF-SIMS and XPS Studies on the Corrosion Behavior of Q-phase in NaCl Solutions As a Function of Ph

Galvanic Corrosion Mechanism of Ti-Al Coupling: the Impact of Passive Films on the Coupling Effect

Predicting Galvanic Corrosion of Aluminum Using Accelerated Laboratory Electrochemical Experiments

Inhomogeneous phases in Cu-Zn-Al-Fe-Mn and the micro-galvanic coupling in 3.5 wt% NaCl solutions at different pH

Assessment of the galvanic corrosion of bi‐metallic couple 7075‐T6‐aluminum alloy/microalloyed dual‐phase steel

Combining AFM imaging and elementally resolved spectro-electrochemistry for understanding stability and quality of passive films formed on Alloy 600

Understanding the Effect of Electrochemical Properties and Microstructure on the Microgalvanic Corrosion of Mg Alloys via Phase-Field Simulations

In-situ AFM and quasi-in-situ studies for localized corrosion in Mg-9Al-1Fe-(Gd) alloys under 3.5 wt.% NaCl environment

Comparative, Real-Time in Situ Monitoring of Galvanic Corrosion in Mg-Mg2Ca and Mg-MgZn2 Couples in Hank's Solution

Galvanic corrosion behavior and numerical simulation of 5083 aluminum alloy and Q235 steel in 3.5% NaCl solution

Microgalvanic Corrosion of Mg–Ca and Mg–Al–Ca Alloys in NaCl and Na2SO4 Solutions

In Situ Corrosion Analysis of Al-Zn-In-Mg-Ti-Ce Sacrificial Anode Alloy

Contribution of the oxygen reduction reaction to the electrochemical cathodic partial reaction for Mg-Al-Ca solid solutions

Distinct phase-selective corrosions of Ti-48Al alloy in aqueous electrolyte and molten salt

Galvanic Corrosion Between Al–Zn–Mg–Cu Alloy and Stainless Steel in the Salt-Spray Atmosphere

Distinctive Localized Corrosion Behavior of Β-Mg2si and Α-Al(fe,mn)si Phases in a 6082 Alloy