Abstract:Electrical energy storage has emerged as a critical component in North America's clean energy transformation. Vehicle electrification and integration of renewables such as wind and solar power into the grid have further underlined the importance of affordable, environmentally friendly energy storage platforms. Rechargeable batteries are now considered to be viable options for large-scale energy storage with lithium-ion and redox flow batteries leading the charge. Over the past decades, aluminum-ion batteries have experienced a renaissance on account of their high volumetric energy density, superior cycleability, enhanced stability and significant cost benefits compared with other commercially available secondary batteries. Aluminum-air batteries also hold significant promise as primary energy storage platforms, but they suffer from thermodynamics and kinetics hurdles, leading to inferior performance. To address these issues, researchers have focused on optimizing different cell components, including anodes, cathodes, and electrolytes. It is well established that nano-structuring battery components would markedly improve their short- and long-term performance by enhancing reaction kinetics. One of the major impediments to wide-scale commercialization of Al-ion batteries continues to be its inferior capacity and cycle stability compared with commercially available secondary batteries. Part of these issues can be ascribed to the failure of cathode materials currently being investigated and used. As for primary Al-air batteries, conventional air cathodes do not perform very well either; and there are many reasons as to why the incorporation of such air cathodes into Al-air batteries would lead to inferior performance or premature failure; the most important of which is low catalytic activity. To address a number of these issues, pulsed current electrodeposition was employed to deposit nano-catalysts such nickel, silver, platinum and oxides of manganese on different support materials, including carbon paper and cloth, titania nanotubes, and stainless steel and nickel meshes. The influence of various electrodeposition parameters, including peak current density, duty cycle, type of waveform and pulse frequency, on resulting layers were systematically investigated. In most cases, nanocatalysts about 2-40 nm in diameter were obtained. Various electrochemical tests were utilized to characterize the resulting layers. A simple mathematical model based on progressive nucleation also was developed to predict the influence of the aforementioned electrodeposition parameters on the resulting nano-catalyst layers. The model was further refined by considering all contributing factors towards growth current, including diffusion, ohmic and charge transfer phenomena as well as changing diffusion coefficients, during electrodeposition. According to the model, at high peak deposition current densities and low duty cycles (5% or less), the ramp-down waveform yielded the highest nucleation rates, confirming the experimental findings in which nanoparticles generated with the above waveform produced the smallest average grain size, ranging from 2-10 nanometer in diameter for platinum and silver nanocatalysts on carbon cloths and titania nanotubes, and 10-50 nm in diameter for nickel nanoparticles deposited on stainless steel and nickel meshes and titania nanotubes.

Impact of surface modification of electrode for aluminium air batteries

Impact of aluminum alloy grade as anode on electrochemical performance for Al‐Air cell in alkaline electrolyte

Evaluation of Impurities in Aluminum Anodes for Al-Air Batteries

Anode Interfacial Layer Construction Via Hybrid Inhibitors for High-Performance Al-Air Batteries.

Experimental Investigation on Various Aluminium Composite Material for Aluminium-Air batteries

Investigation of the Commercial Aluminum Alloys as Anode Materials for Alkaline Aluminum-air Batteries

Development of an Aluminum-Air Battery Using T6-6061 Anode as Electric Vehicle Power Source

Development of Cathodes for Aluminum-Ion and Aluminum-Air Batteries Using Pulsed Electrodeposition

Eco-Sustainable Aluminum-Air Batteries

Effect of Annealing Process on Anode Discharge Performance of Aluminum-Air Batteries

Investigation of Commercial Aluminum Alloys As Anode Materials for Alkaline Aluminum–air Batteries

Electrochemical Performance of Al-1Zn-0.1In-0.1Sn-0.5Mg-xMn (x = 0, 0.1, 0.2, 0.3) Alloys Used as the Anode of an Al-Air Battery

Characterization of the aluminium-air battery utilizing a polypropylene separator with corrosion inhibition ability

Performance improvement for aluminum-air battery by using alloying anodes prepared from commercially pure aluminum

Surface Evolution of Aluminum Electrodes in Non-Aqueous Aluminum Batteries

Impact of Li-ions and CO2 on the electrochemical efficiency of Al and Al-4%Sn in KOH electrolyte for alkaline batteries application

Effects of flocculant and corrosion inhibitor compounding on the electrochemical corrosion behavior of the anode in Al-air batteries

Secondary phase precipitate-induced localized corrosion of pure aluminum anode for aluminum—air battery

The influence of cerium or titanium addition on the corrosion resistance and discharge performance of Al − mg anode for aluminum − air batteries

Excellent Performance of Aluminium Anode Based on Dithiothreitol Additives for Alkaline Aluminium/air Batteries

Aluminum Alloys as Anodes for Aluminum Batteries