Abstract:In order to investigate the effect of solution pH on stress corrosion and electrochemical behavior of aluminum alloy with micro-arc oxidation (MAO) coating, the constant load test and <i>in situ</i> electrochemical impedance spectroscopy (EIS) had been carried out on 7050-T6 aluminum alloys (AA7050-T6) with MAO coating in 3.5 wt% NaCl solution at pH 3, pH 7 and pH 13. EIS was used to evaluate corrosion process of MAO coating and the corresponding equivalent circuit model was established. The results of EIS and mechanical properties of MAO specimens after constant load test exhibited that pH have a significant effect on the corrosion resistance and plasticity of the aluminum alloy with MAO coating. The corrosion resistance was as follows: pH 7 > pH 3 > pH 13. The loss of plasticity was as follows: pH 7 < pH 3 < pH 13. The EIS and the corroded surface morphology demonstrated that the corrosion damage was dominated by pitting corrosion in 3.5%wt NaCl solution at pH 3 and 7. General corrosion was dominant in 3.5%wt NaCl solution at pH 13. In 3.5 wt% NaCl solution at pH 3 and 7, the corrosion resistance decreased at first and then increased at the beginning of corrosion. In the middle stage, the corrosion resistance decreased at first and then stabilized. The corrosion resistance decreased again in the final stage of corrosion. In 3.5 wt% NaCl solution at pH 13, the corrosion resistance decreased at the beginning of corrosion and then increased, and the MAO coating exfoliated completely in the middle stage of corrosion.

Correspondence between susceptibility to SCC of 7050 aluminum alloy and passive film-induced stress at various pH values

Understanding the stress corrosion cracking behavior of 7085-T7651 aluminum alloy in polluted atmosphere

Study on the roles of bisulfite in the stress corrosion cracking of 7050-T7451 aluminum alloy in the thin electrolyte layer environment

Effect of solution pH on stress corrosion and electrochemical behaviour of aluminum alloy with micro-arc oxidation coating

Comparative study of stress corrosion cracking and corrosion-induced mechanical property degradation of 7050-T7451 aluminum alloy in chloride solution containing bisulfite

Quantitative study of the corrosion evolution and stress corrosion cracking of high strength aluminum alloys in solution and thin electrolyte layer containing Cl-

Investigation of the Effect of pH on Stress Corrosion Cracking of API 5L X65 Steel by Impedance Spectroscopy and Slow Strain Rate Tensile Test

An Investigation of Corrosion-Induced Stress During SCC

Stress Corrosion of an Aluminum Alloy in Sodium Chloride Solution under Different Temperatures and Stresses

Effect of NaCl concentration, pH value and tensile stress on the galvanic corrosion behavior of 5050 aluminum alloy

Corrosion Susceptibility of Passive Films on 1060, 2024, and 5083 Aluminum Alloys: Experimental Study and First-Principles Calculations

The influence Cl- on stress corrosion of 7 xxx series aluminium alloys studied by experimental and simulation technology

Synergistic Effects of Corrosion and Slow Strain Rate Loading on the Mechanical and Electrochemical Response of an Aluminium Alloy

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Influence of Interfacial Stress Produced by MAO on Electrochemical Corrosion and Stress Corrosion Cracking Behavior in 7075 Aluminum Alloy

Effect of pH and applied stress on hydrogen sulfide stress corrosion behavior of HSLA steel based on electrochemical noise analysis

The Localized Corrosion and Stress Corrosion Cracking of a 6005A-T6 Extrusion Profile

Determining SCC resistance of stainless steel claddings in high- temperature water by constant load crack growth tests and slow strain rate tests

Corrosion Behavior of 6061 Aluminum Alloy in Simulated SO2-Polluted Seawater

Environmentally assisted stress corrosion cracking behaviour of low alloy steel in SO 2 -containing NaCl solution

Correlation between pitting susceptibility and surface acidity, point of zero charge of passive film on aluminum: Influence of alloying elements