Abstract:The onset of pitting on high purity and ultra high purity aluminum has been studied in the micrometer range by using a microelectrochemical cell in order to evaluate influences that induce localized corrosion. Microelectrochemical tests on polished samples of Al 99.999 and Al 99.9999 in 1 M NaCl showed that pitting at large areas occurred at several hundreds mV more negative than at small areas, suggesting that even very pure Al contains weak points. On rough surfaces weak points are more “activated” than on smooth surfaces. Locally measured pitting potentials of polished samples were shifted to more positive values than those measured on ground samples. Larger areas contain always small scratches, even on polished samples. Hence, the surface roughness showed a minor influence on the onset of pitting on larger areas. Microelectrochemical measurements performed on pure Al 99.99 with small amounts of copper showed that a copper content below 30 ppm is too small to have a beneficial or detrimental effect, whereas a copper content above 300 ppm probably leads to the formation of small inclusions or precipitations that acted as preferential corrosion initiation sites. A copper content around 100 ppm showed a beneficial effect on very small areas but not on larger ones. The onset of pitting on high purity and ultra high purity aluminum has been studied in the micrometer range by using a microelectrochemical cell in order to evaluate influences that induce localized corrosion. In 1 M NaCl we tested the influence of the surface roughness, of the size of the exposed area , and of small amounts of alloyed copper.

Correlation between pitting susceptibility and surface acidity, point of zero charge of passive film on aluminum: Influence of alloying elements

An electrochemical study on corrosion behavior of three alloys in artificial saliva with different pH

Microelectrochemical Studies of Pit Initiation on High Purity and Ultra High Purity Aluminum

Studies on Pitting Corrosion of Al-Cu-Li Alloys Part II: Breakdown Potential and Pit Initiation

First Principles Determination of the Potential-of-Zero-Charge in an Alumina-coated Aluminum/Water Interface Model for Corrosion Applications

Effects of alloying concentration on the aqueous corrosion and passivation of aluminum-manganese-molybdenum concentrated alloys

Corrosion and passive behavior of AlxCrFeNi3−x (x = 0.6, 0.8, 1.0) eutectic high entropy alloys in chloride environment

Corrosion Susceptibility of Passive Films on 1060, 2024, and 5083 Aluminum Alloys: Experimental Study and First-Principles Calculations

First-Principles Modeling of the Repassivation of Corrosion Resistant Alloys: Part II. Surface Adsorption Isotherms for Alloys and the Chloride Susceptibility Index

Susceptibility of chloride ion concentration, temperature, and surface roughness on pitting corrosion of CoCrFeNi medium‐entropy alloy

Corrosion resistance of weight reduced AlxCrFeMoV high entropy alloys

Studies on Pitting Corrosion of Al-Cu-Li Alloys Part III: Passivation Kinetics of AA2098-T851 Based on the Point Defect Model

Systematic Insight into Chloride Concentration, Applied Potential and Time Effect on the Passive Film of Cu-Zn-Ni Ternary Alloy in Alkaline Solution

Correspondence between susceptibility to SCC of 7050 aluminum alloy and passive film-induced stress at various pH values

Electrochemical Corrosion Behaviour of Microcrystalline Aluminium in Acidic Solutions

Correlations among stress corrosion cracking, grain-boundary microchemistry, and Zn content in high Zn-containing Al–Zn–Mg–Cu alloys

Synergism of alloying elements and pitting corrosion resistance of stainless steels

Morphological characteristics and geometric prediction model of pits in complex corrosion environment

Metastable Pitting and Its Correlation with Electronic Properties of Passive Films on Sn–xZn Solder Alloys

Pitting Corrosion of the High-Entropy Alloy Co1.5CrFeNi1.5Ti0.5Mo0.1 in Chloride-Containing Sulphate Solutions

Electrochemical noise features of pure aluminum during pitting corrosion in neutral NaCl solution