Abstract:The impact of Zn on the mechanical properties and corrosion resistance of Al-Mg-Si alloys with high Cu contents was studied through microstructure analysis and accelerated corrosion testing. The age-hardening response of the alloy improved with the addition of trace Zn, and the poor corrosion resistance caused by high Cu content was overcome. Intergranular corrosion susceptibility (IGC) decreased and then increased with increasing Zn content. Al-Mg-Si-Cu alloys that contain 0.5 wt.% Zn possessed the best corrosion resistance. Zn decreased the potential difference between the matrix and the Al(Mn, Fe)Si phases according to scanning Kelvin probe force microscopy (SKPFM) tests, which reduced the driving force of corrosion in the alloy. Additionally, the addition of Zn promoted discontinuous precipitation at the grain boundaries, which was conducive to enhancing the IGC resistance. However, excessive Zn (1.0 wt.%) promoted the diffusion of more solute atoms near the grain boundaries to the grain boundaries, which coarsened the precipitated phase at the grain boundaries and shortened the interphase distance. Moreover, as the width of the PFZ increased, the concentration of solute atoms decreased, and the potential difference between the precipitated phase and the PFZ increased, leading to more severe IGC behavior. Therefore, an appropriate Zn content was beneficial for improving the corrosion properties and age-hardening response of Al-Mg-Si-Cu alloys.

Correlations among stress corrosion cracking, grain-boundary microchemistry, and Zn content in high Zn-containing Al–Zn–Mg–Cu alloys

Correlations Between Stress Corrosion Cracking Susceptibility and Grain Boundary Microstructures for an Al–Zn–Mg Alloy

Investigation on the microstructural evolution and corrosion behaviors of Zn-microalloyed Al-Cu-Li alloys

Effect of Zn/Mg Ratios on SCC, Electrochemical Corrosion Properties and Microstructure of Al-Zn-Mg Alloy

Influence of Alloyed Sc and Zr, and Heat Treatment on Microstructures and Stress Corrosion Cracking of Al–Zn–Mg–Cu Alloys

Effect of Trace Zn on the Mechanical Properties and Corrosion Behavior of Al-Mg-Si Alloys with High Cu

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Influence of Zn Content on Microstructures, Mechanical Properties and Stress Corrosion Behavior of AA5083 Aluminum Alloy

Enhanced Corrosion Performance by Controlling Grain Boundary Precipitates in a Novel Crossover Al-Cu-Zn-Mg Alloy by Optimizing Zn Content

Enhancing Stress Corrosion Cracking Resistance of Low Cu-containing Al-Zn-Mg-Cu Alloys by Slow Quench Rate

Effect of Zn Content on the Microstructure and Properties of Super-High Strength Al-Zn-Mg-Cu Alloys

Effects of Cu Content on Microstructure and Properties of Super-High-strength Al-9.3Zn-2.4Mg-xCu-Zr Alloy

Effect of Zn Addition on the Stress Corrosion Cracking of As-Cast BCC Mg-11Li Based Alloys

Grain Refinement Enhanced Tensile Strength, Fracture Toughness and Fatigue Crack Propagation Resistance of a High Zn-Containing Al-Zn-Mg-Cu Alloy

Effect of Cu Content and Zn/Mg Ratio on Microstructure and Mechanical Properties of Al–Zn–Mg–Cu Alloys

Effects of Critical Defects on Stress Corrosion Cracking of Al–Zn–Mg–Cu–Zr Alloy

Correlation between stress corrosion cracking resistance and grain-boundary precipitates of a new generation high Zn-containing 7056 aluminum alloy by non-isothermal aging and re-aging heat treatment

Coarse Grain Layer On Stress Corrosion Cracking Resistance Of Al-Zn-Mg Alloy

Effect of the Zn/Mg Ratio on Microstructures, Mechanical Properties and Corrosion Performances of Al-Zn-Mg Alloys

Effect of Cr, Yb and Zr Additions on Localized Corrosion of Al–Zn–Mg–Cu Alloy

Influence of Minor Zn Addition on Precipitation Behavior and Intergranular Corrosion Properties of Al-Mg-Si Alloy