Abstract:Hydrogen embrittlement (HE) affects all major high-strength structural materials and as such is a major impediment to lightweighting e.g. vehicles and help reduce carbon-emissions and reach net-zero. The high-strength 7xxx series aluminium alloys can fulfil the need for light, high strength materials, and are already extensively used in aerospace for weight reduction purposes. However, depending on the thermomechanical and loading state, these alloys can be sensitive to stress-corrosion cracking (SCC) through anodic dissolution and hydrogen embrittlement. Here, we study at the near-atomic-scale the intra- and inter-granular microstructure ahead and in the wake of a propagating SCC crack. Moving away from model cases not strictly relevant to application, we performed an industry-standard test on an engineering Al-7XXX alloy. H is found segregated to planar arrays of dislocations and to grain boundaries that we can associate to the combined effects of hydrogen-enhanced localized plasticity (HELP) and hydrogen-enhanced decohesion (HEDE) mechanisms. We report on a Mg-rich H-rich amorphous oxide on the corroded crack surface and evidence of Mg-related diffusional processes leading to dissolution of the strengthening eta-phase precipitates ahead of the crack. We show ingress of up to 1 at% O, i.e. well above the solubility limit of O in Al, near the oxide-metal interface, while no increased level of H is found in the matrix. We provide an array of discussion points relative to the interplay of structural defects, transport of solutes, thereby changing the resistance against crack propagation, which have been overlooked across the SCC literature and prevent accurate service life predictions.

Comparative study of stress corrosion cracking and corrosion-induced mechanical property degradation of 7050-T7451 aluminum alloy in chloride solution containing bisulfite

Study on the roles of bisulfite in the stress corrosion cracking of 7050-T7451 aluminum alloy in the thin electrolyte layer environment

Understanding the stress corrosion cracking behavior of 7085-T7651 aluminum alloy in polluted atmosphere

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Quantitative study of the corrosion evolution and stress corrosion cracking of high strength aluminum alloys in solution and thin electrolyte layer containing Cl-

The Localized Corrosion and Stress Corrosion Cracking of a 6005A-T6 Extrusion Profile

Corrosion Behavior and Mechanical Performance of 7085 Aluminum Alloy in a Humid and Hot Marine Atmosphere

Revisiting stress-corrosion cracking and hydrogen embrittlement in 7xxx-Al alloys at the near-atomic-scale

Evaluation of residual stress relief of aluminum alloy 7050 by using crack compliance method

Correspondence between susceptibility to SCC of 7050 aluminum alloy and passive film-induced stress at various pH values

Impact of Marine Atmospheric Corrosion on the Microstructure and Tensile Properties of 7075 High-Strength Aluminum Alloy

Synergistic Effects of Corrosion and Slow Strain Rate Loading on the Mechanical and Electrochemical Response of an Aluminium Alloy

Study on mechanical properties and hydrogen embrittlement susceptibility of 7075 aluminium alloy

Analysis of Stress Corrosion Cracking Growth Rate in the Heat-Affected Zone of 316L Based on the Heterogeneity of the Mechanical Properties

Influence of Interfacial Stress Produced by MAO on Electrochemical Corrosion and Stress Corrosion Cracking Behavior in 7075 Aluminum Alloy

Study on corrosion, hydrogen permeation, and stress corrosion cracking behaviours of AISI 4135 steel in the tidal zone

Comparative study on the stress corrosion cracking of a new Ni-advanced high strength steel prepared by TMCP, direct quenching, and quenching & tempering

An Investigation of Corrosion-Induced Stress During SCC

The single effect of microstructure, residual strain and geometric structure on the stress corrosion cracking behavior of scratched alloy 690TT

Influence of AC/DC on stress corrosion cracking of Ti-6Al-3Nb-2Zr-1Mo alloy in simulated marine solution