Abstract:Titanium/nanodiamond (ND) mixtures were sintered using spark plasma sintering (SPS). Densification was studied for Ti + x wt% ND mixtures (where x = 2, 5, 10 and 15) to determine the optimized cycles. Ti/ND mixtures were then sintered under these optimized conditions achieving relative densities higher than 96 %. The SPS temperatures for the Ti + 2 wt% ND, Ti + 5 wt% ND, Ti + 10 wt% ND and Ti + 15 wt% ND mixtures were 1000 °C, 1050 °C, 1150 °C and 1150 °C, respectively. Numerical simulation by finite elements were used to check the thermal homogeneity in the sample and to determine the maximal temperature in the sample to ensure avoiding graphitization. The effects of ND on the Ti/ND mixtures were investigated. Microstructural characterizations reveal the presence of three different phases including a Ti phase, a non-stoichiometric TiC x solid phase and NDs located inside the TiC x grains. Indeed, NDs react with Ti to form the TiC x solid phase. However, a fast sintering with temperature below graphitization of diamond allows to keep nanodiamond structure into the Ti/ND mixtures. Hardness and electrical conductivity of the Ti/ND mixtures were measured. The results show that the higher the ND content, the more the hardness of the composite increases and the more the electrical conductivity decreases. Hardness increased from 340 HV to 1346 HV for Ti and the Ti + 15 wt% ND mixture, respectively. Electrical conductivity is reduced by a factor of three for the Ti + 15 wt% ND mixture relative to Ti which can be explained by the microstructure exhibiting fewer Ti grains in favor of the TiC x solid phase when ND content was increased in the composite.

Effects of Diamond on the Mechanical Properties and Thermal Conductivity of Si3N4 Composites Fabricated Using Spark Plasma Sintering

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Fabrication and characterization of highly thermal conductive Si3N4/diamond composite materials

Rapid fabrication of the Ti3SiC2 bonded diamond composite by spark plasma sintering

Effects of spark plasma sintering and the nanodiamond amount on titanium-nanodiamond composite properties

Effect of diamond content on microstructure and properties of C/SiC-diamond composites

Research on maximizing the diamond content of diamond/SiC composite

Diamond–SiC nanocomposites sintered from a mixture of diamond and silicon nanopowders

Effect of Si-coated diamond on the relative density and thermal conductivity of diamond/W composites prepared by SPS

Effect of Composite Sintering Additives Containing Non-Oxide on Mechanical, Thermal and Dielectric Properties of Silicon Nitride Ceramics Substrate

A Novel TiB2–SiC Composite Doped with Diamond Nanoparticles: Densification, Microstructure, and Thermal Properties

Effect of Multi-Sintering Additive MgO-Al2O3-CeO2 on Densification and Properties of Silicon Nitride Ceramics by Spark Plasma Sintering

Micron Diamond Composites with Nanocrystalline Silicon Carbide Bonding

Fluoride doped SiC/Si3N4 composite as a high thermal conductive material with enhanced mechanical properties

Superhard Composites of Cubic Silicon Nitride and Diamond

Effect of Tungsten Carbide on Densification and Mechanical Properties of Silicon Nitride Ceramics by Spark Plasma Sintering

Effects of Ti(C, N) addition on the microstructure and mechanical properties of spark plasma sintered Si3N4/Ti(C, N) ceramic tool material

Preparation of diamond/SiC composites by the liquid silicon infiltration method and their microstructure and properties

The Effect of CNTs on the Spark Plasma Sintering Densification Behavior and Mechanical Properties of B4C-Si Powders

Effects of sintering additives on mechanical properties and microstructure of Si3N4 ceramics by microwave sintering

Preparation of bimodal-diamond/SiC composite with high thermal conductivity