Abstract:This article describes spark plasma sintering of ceramics based on silicon carbide with nanoadditives, as follows: MnOnano 5.5 wt. % + Al2O3nano 2.0 wt. % + SiCnm (37–57 wt. %) + SiCμm (31–51 wt. %) + SiO2μm 4.5 wt. %. Sintering was carried out at 2000 °C. The diffraction pattern of the analyzed sample showed the presence of silicon carbide with a hexagonal crystal lattice. Residual amounts of rhombohedral SiC, α-Fe, and a solid solution of silicon in iron were also found. The method of thermogravimetric analysis established the change in mass, heat flow, temperature of the samples, and the change in the partial pressures of gases during the experiment. Samples obtained by SPS show a higher density of the material at the level of 3.3 g/cm3, average mechanical strength of 454 MPa, and microhardness of 35 GPa, compared with samples obtained by liquid-phase sintering. The SPS method also made it possible to obtain materials with a higher density (by 8%) and practically no significant crystal growth compared to samples obtained by liquid phase sintering. The results of the study facilitate the achievement of a combination of new approaches to the design of compositions and the technology of manufacturing SiC ceramics, which significantly expands their areas of application.

Effect of Multi-Sintering Additive MgO-Al2O3-CeO2 on Densification and Properties of Silicon Nitride Ceramics by Spark Plasma Sintering

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Effects of MgAl2O4-ZrO2 Addition on Sintering Behaviors and Mechanical Properties of Silicon Nitride Ceramics

Effect of Sintering Temperature and Yttrium Composition on the Densification, Microstructure and Mechanical Properties of Spark Plasma Sintered Silicon Nitride Ceramics with Al2O3 and Y2O3 Additives

Sintering and microstructure of silicon nitride with magnesia and cerium additives

Effects of sintering additives on mechanical properties and microstructure of Si3N4 ceramics by microwave sintering

Effect of Sintering Additives on Microstructure and Mechanical Properties of Porous Silicon Nitride Ceramics

Effect of Composite Sintering Additives Containing Non-Oxide on Mechanical, Thermal and Dielectric Properties of Silicon Nitride Ceramics Substrate

The influence of magnesium compounds on the properties of silicon nitride ceramics

Effect of additive content on the microstructure and room‐temperature and high‐temperature mechanical properties of Si3N4 ceramics

Effect of MgO/CeO2 on Pressureless Sintering of Silicon Nitride

Structure and Properties of Spark Plasma Sintered SiC Ceramics with Oxide Additives

The Role of MgSiN2 During the Sintering Process of Silicon Nitride Ceramic

Effect of Different Sintering Additives on the Microstructure, Phase Compositions and Mechanical Properties of Si3N4/SiC Ceramics

Effect of Sintering Additive Composition on Microstructure and Mechanical Properties of Silicon Nitride

Improved Mechanical Properties of Dense Β-Si3n4 Ceramics Fabricated by Spark Plasma Sintering with Al2O3-YSZ Additives

Effect of In-Situ Formed MoSi2 on Phase Transformation and Thermal Diffusivity of Spark Plasma Sintered Silicon Nitride

Effect of Different Sintering Additives on the Reaction-Bonded Si3N4/SiC Composite Ceramics

Effect of MgF2 addition on mechanical properties and thermal conductivity of silicon nitride ceramics

Effects of Sintering Additives on Properties of Porous Silicon Nitride Ceramics Fabricated by Carbothermal Reduction

Study of Rare-Earth Oxide Sintering Additive Systems for Spark Plasma Sintering AlN Ceramics