Abstract:Titanium/nanodiamond (ND) mixtures were sintered using spark plasma sintering (SPS). Densification was studied for Ti + x wt% ND mixtures (where x = 2, 5, 10 and 15) to determine the optimized cycles. Ti/ND mixtures were then sintered under these optimized conditions achieving relative densities higher than 96 %. The SPS temperatures for the Ti + 2 wt% ND, Ti + 5 wt% ND, Ti + 10 wt% ND and Ti + 15 wt% ND mixtures were 1000 °C, 1050 °C, 1150 °C and 1150 °C, respectively. Numerical simulation by finite elements were used to check the thermal homogeneity in the sample and to determine the maximal temperature in the sample to ensure avoiding graphitization. The effects of ND on the Ti/ND mixtures were investigated. Microstructural characterizations reveal the presence of three different phases including a Ti phase, a non-stoichiometric TiC x solid phase and NDs located inside the TiC x grains. Indeed, NDs react with Ti to form the TiC x solid phase. However, a fast sintering with temperature below graphitization of diamond allows to keep nanodiamond structure into the Ti/ND mixtures. Hardness and electrical conductivity of the Ti/ND mixtures were measured. The results show that the higher the ND content, the more the hardness of the composite increases and the more the electrical conductivity decreases. Hardness increased from 340 HV to 1346 HV for Ti and the Ti + 15 wt% ND mixture, respectively. Electrical conductivity is reduced by a factor of three for the Ti + 15 wt% ND mixture relative to Ti which can be explained by the microstructure exhibiting fewer Ti grains in favor of the TiC x solid phase when ND content was increased in the composite.

A Novel TiB2–SiC Composite Doped with Diamond Nanoparticles: Densification, Microstructure, and Thermal Properties

Nanostructured Diamond-Tic Composites with High Fracture Toughness

Role of co-addition of BN and SiC on microstructure of TiB2-based composites densified by SPS method

Effects of spark plasma sintering and the nanodiamond amount on titanium-nanodiamond composite properties

Densification behavior and microstructure development in TiB2 ceramics doped with h-BN

Reaction Mechanism of Ti<SUB>3</SUB>SiC<SUB>2</SUB> Formed on the Diamond

Reaction mechanism of Ti3SiC2 formed on the diamond

Spark plasma sintering of TiN ceramics codoped with SiC and CNT

A microstructural approach to the chemical reactions during the spark plasma sintering of novel TiC–BN ceramics

Fabrication and characterization of highly thermal conductive Si3N4/diamond composite materials

Effects of Diamond on the Mechanical Properties and Thermal Conductivity of Si3N4 Composites Fabricated Using Spark Plasma Sintering

Rapid fabrication of the Ti3SiC2 bonded diamond composite by spark plasma sintering

Densification, Microstructure, and Wear Properties of TiB2-TiC-GNP and TiB2-TiC-BN Composites

Preparation of bimodal-diamond/SiC composite with high thermal conductivity

Fabrication of (Zr,Ti)B2-ZrN-BN composites through reactive spark plasma sintering of ZrB2 and TiN

Thermal conduction and strength of diamond-copper composite sandwich obtained by SPS diffusion bonding with Ti interlayer

Preparation of TiB2–SiC composites toughened with interlocking microstructure by self-assembled TiB2 plates

Effect of Si-coated diamond on the relative density and thermal conductivity of diamond/W composites prepared by SPS

Spark plasma sintering of TiN–TiB2–hBN composites and their properties

Evaluation of the Wear and Mechanical Properties of Titanium Diboride-Reinforced Titanium Matrix Composites Prepared by Spark Plasma Sintering

Fabrication of Ti2AlC ceramic bonded diamond composites by self-propagation high temperature sintering