Abstract:Calorimetric measurements of AC loss and hence interstrand contact resistance (ICR), were measured on three samples of Rutherford cable wound with Cu-stabilized jelly-roll type unplated Nb3Al strand. One of the cable types was furnished with a thin core of AISI 316L stainless steel and the other two were both uncored but insulated in different ways. The cables were subjected to a room-temperature-applied uniaxial pressure of 12 MPa that was maintained during the reaction heat treatment (RHT), then vacuum impregnated with CTD 101 epoxy, and repressurized to 100 MPa during AC-loss measurement. The measurements were performed at 4.2 K in a sinusoidal field of amplitude 400 mT at frequencies of 1 to 90 mHz (no DC-bias field) that was applied both perpendicular and parallel to the face of the cable (the face-on, FO, and edge-on, EO, directions, respectively). For the cored cable the FO-measured effective ICR (FO-ICR), was 5.27 . Those for the uncored cables were less than 0.08 . As shown previously for NbTi- and Nb3Sn-based Rutherford cables, the FO-ICR can be significantly increased by the insertion of a core, although in this case it is still below the range recommended for accelerator-magnet use. Post-measurement dissection of one of the cables showed that the impregnating resin had permeated between the strands and coated the core with a thin, insulating layer excepting for some sintered points of contact. In the uncored cables the strands were coated with resin except for the points of interstrand contact. It is suggested that in the latter case this tendency for partial coating leads to a processing-sensitive FO-ICR.

Control of contact resistance by strand surface coating in 36-strand NbTi CICCs

AC Loss and Contact Resistance In Copper-Stabilized Nb3Al Rutherford Cables with and without a Stainless Steel Core

Almost Kahler 4-manifolds with J-invariant Ricci tensor and special Weyl tensor

Electrical Contact Resistance in REBCO Stacks and Cables With Modified Surfaces

Metallographic Investigation of First Full-Size High-Jc Nb3Sn Cable-in-conduit Conductor after Cyclic Loading Tests

Numerical Simulation of the Mechanical Properties of the $\hbox{nb}_{3}\hbox{sn}$ CICCs under Transverse Cyclic Loads

Deformation Behavior and Degradation on Rutherford Cabling of Nb 3 Sn Wires

Indentation Effects on Strain Sensitivity of Critical Current for Internal-Tin Nb3Sn Strand

Numerical Investigation on Transverse Heat Transfer Properties in Cross Section of Full Size Nb3Sn CICC ITER Conductor

Contact resistivity due to oxide layers between two REBCO tapes

Fabrication of Low AC Loss Cu0.5Mn-Based NbTi Superconducting Strands

Multi-contact behaviors among Nb3Sn strands associated with load cycles in a CS1 cable cross section

CORD, A Novel Numerical Mechanical Model for ${\rm Nb}_{3}{\rm Sn}$ CICCs

Enhanced Normal Zone Propagation Velocity in REBCO Coated Conductors Using an Intermetallic Stabilizer Coating

DC Performance Measurement and Assessment of Nb 3 Sn Cable-In-Conduit Conductor for CFETR CS Model Coil

The Possible Control Method of Turn-to-Turn Contact Resistivity of REBCO Coil by Surface Coating

Effect of the Cu Stabilisation Layer on the Turn-to-turn Contact Resistance of a Non-Insulated REBCO Winding

Local Plastic Deformation Effects on the Critical Current of High-Jc Nb3Sn Strands under Uniaxial Strain

CORD, A Novel Numerical Mechanical Model for CICCs

High Performance of an Innovative Cable-in-conduit Conductor with CWS Cable Pattern

Direct measurement of inter-filament resistance in Nb3Sn multi-filamentary strands