Abstract:Different microstructures were obtained under various thermal conditions by adjusting the heat treatment parameters of the Cr-Co-Ni-Mo series of ultra-high strength stainless steel. The effect of organizational evolution on the stress corrosion cracking (SCC) of the Cr-Co-Ni-Mo series of ultra-high strength stainless steel was investigated using potentiodynamic polarization curves, electrochemical impedance spectroscopy (EIS), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and other test methods in combination with slow strain rate tensile tests (SSRTs). The results show that the Mo- and Cr-rich clusters and precipitation of the Laves phase reduce the corrosion resistance, while increasing the austenite content can improve the corrosion resistance. The Cr-Co-Ni-Mo series of ultra-high strength stainless steel has a high SCC resistance after quenching at 1080 °C and undergoing deep cooling (DC) treatment at −73 °C. With increasing holding time, the strength of the underaged and peak-aged specimens increases, but the passivation and SCC resistance decreases. At the overaged temperature, the specimen has good SCC resistance after a short holding time, which is attributed to its higher austenite content and lower dislocation density. As a stable hydrogen trap in steel, austenite effectively improves the SCC resistance of steel. However, under the coupled action of hydrogen and stress, martensitic transformation occurs due to the decrease in the lamination energy of austenite, and the weak martensitic interface becomes the preferred location for crack initiation and propagation.

The Effect of Nano-Sized Precipitates on Stress Corrosion Cracking Propagation of Alloy 718 under Constant Loads in PWR Primary Water

Understanding the Effect of Nanosized NbC Precipitates on the Stress Corrosion Cracking of High-Strength Low-Alloy Steel in a Simulated Deep-Sea Environment

Effect of different loading conditions on corrosion fatigue crack growth rate of a nickel-based alloy in supercritical water

Quantification of SCC mechanisms in austenitic alloys under PWR primary water conditions

The Effect of Stress Gradient on the Formation of TCP Phases in a Ni-based Single Crystal Superalloy at 1050 Oc

Stress Corrosion Cracking of High-Strength Ni-Base Alloys in PWR Primary Water Containing KOH vs. LiOH

The correlation between the dislocation slip/grain boundary interaction mode and the resistance to SCC initiation of Alloy 690 in simulated PWR primary water

The single effect of microstructure, residual strain and geometric structure on the stress corrosion cracking behavior of scratched alloy 690TT

Stress corrosion crack propagation affected by microstructures for nuclear steam turbine rotor steels in the simulated environment

On the role of intergranular nanocavities in long-term stress corrosion cracking of Alloy 690

Quantitatively evaluating the contribution of intergranular carbides, Cr-depleted zone, and grain boundary to intergranular stress corrosion cracking of Alloy 600 in a simulated boiling water reactors environment with high oxygen concentrations

Effect of material chemical composition on oxidation and stress corrosion cracking of the submerged arc welding Alloy 52M overlay in a simulated PWR primary water

Insight into the acceleration in oxidation kinetics ahead of stress corrosion crack of alloy 690 in simulated PWR primary water

Comparison of the effect of water jet cavitation peening on stress corrosion cracking behavior of nickel-based alloy 600 and alloy 182 in high temperature water

Intergranular precipitation behavior and its influence on the stress relaxation cracking susceptibility of Super304H austenitic stainless steel weld metal during long-term aging

Effect of dissolved oxygen and hydrogen on the stress corrosion cracking behavior of alloy 600 in high temperature water

Effect of Stress Ratio on the Fatigue Crack Propagation Behavior of the Nickel-based GH4169 Alloy

Effect of zinc injection on mitigating stress corrosion cracking initiation of structural materials in light water reactor primary water

Correlating oxidation resistance to stress corrosion cracking of 309L and 308L stainless steel claddings in simulated PWR primary water

Effect of Organizational Evolution on the Stress Corrosion Cracking of the Cr-Co-Ni-Mo Series of Ultra-High Strength Stainless Steel

Surface Finishing Effect on Stress Corrosion Cracking Test Results of Alloy 600 by Uni-Axial Constant Load Test in Hydrogenated Steam Environment