Abstract:BackgroundUnder the condition of sub-cooled nucleate boiling (SNB), corrosion products in primary coolant of nuclear reactor will deposit on the outer surface of fuel cladding, which is commonly called fuel crud. Previous literature shown, zinc injection in primary coolant is an important method to inhibit the fuel crud deposition on the fuel cladding surface.PurposeThis study aims to investigate the influence of zinc concentration on the behavior of fuel crud deposition, and eventually provide guidance for zinc injection in primary coolant of nuclear power plant.MethodsThe fuel crud deposition tests of domestic zirconium alloy fuel cladding in different zinc concentrations were carried out by using a self-made fuel crud deposition device. Tubular crud deposition test specimen with built-in heating unit was designed and prepared for simulation study. After the tests, stereo microscope (SM) and scanning electron microscope (SEM) were employed to observe the macro and micro morphology of fuel crud whilst the composition of of fuel crud was observed and analyzed by the energy dispersive spectroscopy (EDS) with SEM, and X-ray photoelectron spectroscopy (XPS) was used to analyze the contents of Zn and B elements in the crud phase and inside the crud.ResultsObservation results show that the chimney-like crud formed on the fuel cladding surface becomes less obvious with increasing the zinc concentration in the coolant and the crud surface becomes flatter. Simutabeously, the crud thickness, the ratio of Ni/Fe and the boron precipitation mass within the crud are decreasing with increase of the zinc concentration. When the zinc concentration increases to 100 μg‧L-1, new Zn-containing phases precipitate within the crud.ConclusionsWithin the zinc concentration of 0~100 μg‧L-1, zinc injection in primary coolant of reactor can significantly inhibit the crud deposition on the fuel cladding surface.

Effect of zinc injection on mitigating stress corrosion cracking initiation of structural materials in light water reactor primary water

Role of Zn injection on mitigating stress corrosion cracking initiation of Alloy 182 weld metal in simulated light water reactor environment

Effects of Zinc Injection on Stress Corrosion Cracking of Cold Worked Austenitic Stainless Steel in High-Temperature Water Environments

Effects of Zn injection on the oxide film characteristics of zirconium alloy fuel cladding exposed to high-temperature pressurized water with or without subcooled nucleate boiling

Effects of Zn injection on corrosion behavior and crud deposition of FeCrAl fuel cladding under subcooled nuclear boiling condition in high-temperature pressurized water

Some Fundamental Understandings of Zn-injection Water Chemistry on Material Corrosion in Pressurized Water Reactor Primary Circuit

Effect of Zn Injection on Established Surface Oxide Films on 316 L Stainless Steel in Borated and Lithiated High Temperature Water

Effects of zinc-aluminium injection on corrosion behaviour and semiconductor properties of carbon steel in the PHT system of PHWR

Research on the effects of corrosion resistant zinc injection in primary circuit of large-scale PWR plants on core crud amount

Corrosion Behavior of High-Strength Low-Alloy Steel in High-Temperature Water with Zinc and Aluminum Simultaneous Injection

Stress Corrosion Cracking of 316l Haz for 316l Stainless Steel/Inconel 52m Dissimilar Metal Weld Joint in Simulated Primary Water

Effects of Precipitation on the Stress Corrosion Crack Initiation of Alloy 718 in Simulated Pressurized Water Reactor Primary Environment

Environmentally Assisted Cracking of Forged 316LN Stainless Steel and Its Weld in High Temperature Water

The Effect of Nano-Sized Precipitates on Stress Corrosion Cracking Propagation of Alloy 718 under Constant Loads in PWR Primary Water

Effect of zinc injection on crud deposition and boron precipitation on fuel cladding surface

Stress Corrosion Cracking in the Heat Affected Zone of A Stainless Steel 308L-316L Weld Joint in Primary Water

Characterizing the Effects of In-Situ Sensitization on Stress Corrosion Cracking of Austenitic Steels in Supercritical Water

Evaluation of Stress Corrosion Cracking Susceptibility of Forged 316 Stainless Steel in Simulated Primary Water

Electrochemical and Surface Analytical Investigation of the Effects of Zn Concentrations on Characteristics of Oxide Films on 304 Stainless Steel in Borated and Lithiated High Temperature Water

Thermodynamic Analysis and Crystallographic Properties of MFe2O4, MCr2O4 and MAl2O4 (M = Fe, Ni, Zn) Formed on Structural Materials in Pressurized Water Reactor Primary Circuit under Zinc and Zinc-aluminum Water Chemistry

Investigations on the SCC initiation behavior of cold worked 316L in high temperature oxygenated water at constant loads