Abstract:Low alloy SA508 bainitic steel is often welded to 300 series austenitic stainless steel in nuclear power plants. These dissimilar metal weldments use 309L butter applied to the low alloy steel and 308L groove filler material to join the 309L to austenite. High alloy steels (such as the 308L and 309L material used here) have been identified as having greater susceptibility to irradiation-assisted stress corrosion cracking (IASCC). Evidence is presented here of cracking under tensile loads in 309L weldment butter in LWR hydrothermal conditions that correlates irradiation induced changes at δ ferrite−γ austenite phase boundaries and γ−γ grain boundaries; specifically intergranular Cr 23 C 6 precipitates. Cracking is not observed in irradiated 308L groove filler under the same conditions. Both the 309L butter and 308L filler material have a duplex or mixed δ−γ phase microstructure due to solidification during the welding procedure. We have performed constant extension rate autoclave immersion tests in BWR normal water chemistry hot water (288 °C, 10 MPa, 2000 wt. ppb dissolved oxygen, <100 nS/cm conductivity, neutral pH) of proton irradiated (2 MeV, approximately 3 displacements per atom at a depth of 10 μm). Proton irradiation to the dpa levels used here induced Cr 23 C 6 carbide precipitation at γ−γ grain boundaries and δ−γ phase boundaries in the 309L butter but not the 308L filler. Cracking was observed in the proton-irradiated volume of 309L at these interfaces in the vicinity of the Cr 23 C 6 precipitates. We hypothesis the SA508 is the source of carbon in the 309L butter. Cr depletion at γ−γ grain boundaries was also observed and may also be a root cause of cracking. The 309L butter is under significant tensile residual stress in the weldment that adds to applied tensile loads and this too may be a contributing factor.

A high-resolution characterization of irradiation-assisted stress corrosion cracking of proton-irradiated 316L stainless steel in simulated pressurized water reactor primary water

IASCC of neutron irradiated 316 stainless steel to 125 dpa

Irradiation Assisted Stress Corrosion Cracking of 347 Stainless Steel in Simulated PWR Primary Water containing Lithium Hydroxide or Potassium Hydroxide

Decoupling the roles of grain boundary oxidation and stress in IASCC of neutron-irradiated 304L stainless steel

The time dependence of proton irradiation effect on the intergranular oxidation of 316L stainless steel in high-temperature hydrogenated water

A micromechanical analysis of intergranular stress corrosion cracking of an irradiated austenitic stainless steel

Clarifying the mitigation effect of proton irradiation on the intergranular oxidation of 316L stainless steel in high temperature water

How irradiation promotes intergranular stress corrosion crack initiation

Crack initiation of neutron-irradiated 304 L stainless steel in PWR primary water

Irradiation-assisted cracking of SA508-304L weldments with 308L groove filler and 309L butter in hot water immersion constant rate extension tests

Effect of heavy ion irradiation on the electrochemical behavior of 321 stainless steel

Unveiling the synergistic effect of thermal aging and irradiation corrosion on the passivation performance and stress corrosion cracking of 308 L stainless steel under high-temperature water environment

Clarifying the irradiation effect on the general oxidation of 316L stainless steel in high temperature hydrogenated water after 1000 h immersion

Investigation of Stress Corrosion Cracking Resistance of Irradiated 12Cr Ferritic-Martensitic Stainless Steel in Supercritical Water Environment

Correlating oxidation resistance to stress corrosion cracking of 309L and 308L stainless steel claddings in simulated PWR primary water

The effect of potassium hydroxide primary water chemistry on the IASCC behavior of 304 stainless steel

Quantitatively evaluating the contribution of intergranular carbides, Cr-depleted zone, and grain boundary to intergranular stress corrosion cracking of Alloy 600 in a simulated boiling water reactors environment with high oxygen concentrations

Effects of pressurized water reactor environment and cyclic loading parameters on the low cycle fatigue behavior of 304L stainless steel

Correlating microstructure and mechanical properties of harvested high dose Zorita light water reactor internals

Intergranular stress distributions in polycrystalline aggregates of irradiated stainless steel

Irradiation damage and corrosion performance of proton irradiated 304 L stainless steel fabricated by laser-powder bed fusion