Abstract:Twin grain boundaries (GBs) are found to be inherently resistant to stress corrosion cracking (SCC), which has become one of the main failure mechanisms of steam generator (SG) tubing since the 1980s and brings huge economic losses to the nuclear power plants. As it is a widely used material for SG tubing, the SCC-resistance of the twins in Alloy 690TT in 10 wt.% sodium hydroxide solution with 100 ppm litharge at 330 degrees C was studied using C-ring samples. The relationship between the crack paths, twin GBs and the residual strains in the studied areas were analyzed using an environmental scanning electron microscope (ESEM) equipped with electron backscatter diffraction (EBSD) equipment. A continuously stressed C-ring sample without immersion was used to evaluate the effect of residual stress or strain on the microstructure of the twin GBs. The oxides at the crack paths were analyzed by an energy dispersive spectroscopy (EDS). The results show that many twin GBs are cracked during crack propagation. There are more twins with large deviations from the ideal Sigma 3 twin misorientation in the studied area where the residual strain is high. In situ EBSD analyses verify that higher residual strain causes twins to deviate from the ideal twin microrientation and can even promote twins transiting into random high angle grain boundaries, when the residual strain is high enough. The EDS result illustrates that litharge accelerates the dissolution of the chromium and nickel in the matrix. Overall, the SCC-resistance of the twins in Alloy 690TT in the studied solution is reduced by the destruction of the ideal microrientation of the twin GBs and the preferential dissolution of chromium and nickel at the crack paths. Higher residual strain on the Alloy 690TT and deleterious impurities in the circulating secondary water should be eliminated during the operation of nuclear power plants. (C) 2011 Elsevier B.V. All rights reserved.

On the role of intergranular nanocavities in long-term stress corrosion cracking of Alloy 690

Microstructural Study on the Stress Corrosion Cracking of Alloy 690 in Simulated Pressurized Water Reactor Primary Environment

Insights into the stress corrosion cracking of solution annealed alloy 690 in simulated pressurized water reactor primary water under dynamic straining

Study of the Influence of Microstructure and Intergranular Carbides on the Oxidation Behavior of a Nickel Base Alloy 690 TT in Supercritical Water Nuclear Reactor Conditions

Creep Residual Life Prediction of a Nickel-Based Single Crystal Superalloy Based on Microstructure Evolution

Insights into stress corrosion cracking in scratched area of alloy 690TT steam generator tubes

Trans-twins Stress Corrosion Cracking Behaviors of Alloy 690TT in Lead-Containing Caustic Solution at 330°C

High cycle fatigue behavior and numerical evaluation of Alloy 690TT steam generator tube

Quantitatively evaluating the contribution of intergranular carbides, Cr-depleted zone, and grain boundary to intergranular stress corrosion cracking of Alloy 600 in a simulated boiling water reactors environment with high oxygen concentrations

Effect of Intergranular Carbides on the Cracking Behavior of Cold Worked Alloy 690 in Subcritical and Supercritical Water

Microstructure and stress corrosion cracking behavior of Alloy 690TT steam generator tubes with internal bulge defect

Stress corrosion crack initiation in Alloy 690 in high temperature water

Strain Rate Dependence of the Effect of Intergranular Carbides on the Resistance to Stress Corrosion Cracking Initiation of Alloy 690 in Simulated Pwr Primary Water

Characterization of Stress Corrosion Cracking Initiation Precursors in Cold-Worked Alloy 690 Using Advanced High-Resolution Microscopy

Characterizing the Effect of Creep on Stress Corrosion Cracking of Cold Worked Alloy 690 in Supercritical Water Environment

Quantification of SCC mechanisms in austenitic alloys under PWR primary water conditions

A High-Resolution Characterization of the Initiation of Stress Corrosion Crack in Alloy 690 in Simulated Pressurized Water Reactor Primary Water

Effect of Cold Work on the Stress Corrosion Cracking Behavior of Alloy 690 in Supercritical Water Environment

High Temperature Fatigue and Creep-Fatigue Behaviors in a Ni-based Superalloy: Damage Mechanisms and Life Assessment

Fretting Corrosion-Induced Microstructural Evolution of Alloy 690TT Tube in High Temperature Pressurised Water

The correlation between the dislocation slip/grain boundary interaction mode and the resistance to SCC initiation of Alloy 690 in simulated PWR primary water