Abstract:High-carbon and high-chromium alloy steels are prone to pitting and intergranular corrosion, which reduces corrosion resistance. The precipitation behavior of the carbides of high-carbon and high-chromium alloy steels is one of the main factors affecting pitting and intergranular corrosion of stainless steel. In this study, 5Cr15MoV stainless steel was heated to 1,200celcius and then cooled by cooling rates varying from 25 to 150 degrees C/min. The precipitation behavior of grain boundary carbides of 5Cr15MoV steel at different cooling rates, and its effect on the corrosion resistance of materials was studied. The results show that the carbides of 5Cr15MoV steel mainly precipitate along the grain boundaries, which leads to the formation of chromium-depleted zones near the grain boundaries and reduces resistance to intergranular corrosion. It has been found that a higher cooling rate shortens the width of the Cr-depleted zone near the boundary from 0.871 to 0.569 mu m, reduces the Cr-concentration gradient near the grain boundary from 36.422% to 12.667%, and suppresses the nucleus growth rate of grain boundary carbides. As the cooling rate increases, the corrosion current density decreases from 13.29 to 2.42 mu A/cm(2). The corrosion rate is the lowest, while the cooling rate is 150 degrees C/min. The corrosion rate decreases from 218.339 to 158.488 mm/a. The phenomenon of intergranular corrosion and pitting corrosion was found to be weakened; and thereby, it is shown that an intensive cooling rate can improve the corrosion resistance of 5Cr15MoV steel.

Strain Rate Dependence of the Effect of Intergranular Carbides on the Resistance to Stress Corrosion Cracking Initiation of Alloy 690 in Simulated Pwr Primary Water

The correlation between the dislocation slip/grain boundary interaction mode and the resistance to SCC initiation of Alloy 690 in simulated PWR primary water

Insight into the acceleration in oxidation kinetics ahead of stress corrosion crack of alloy 690 in simulated PWR primary water

Quantitatively evaluating the contribution of intergranular carbides, Cr-depleted zone, and grain boundary to intergranular stress corrosion cracking of Alloy 600 in a simulated boiling water reactors environment with high oxygen concentrations

Stress corrosion crack initiation in Alloy 690 in high temperature water

On the role of intergranular nanocavities in long-term stress corrosion cracking of Alloy 690

The single effect of microstructure, residual strain and geometric structure on the stress corrosion cracking behavior of scratched alloy 690TT

Effects of Cooling Rate on the Precipitation Behavior of Grain Boundary Carbide and Corrosion Resistance of 5cr15mov Stainless Steel

Effect of different loading conditions on corrosion fatigue crack growth rate of a nickel-based alloy in supercritical water

Study of the Influence of Microstructure and Intergranular Carbides on the Oxidation Behavior of a Nickel Base Alloy 690 TT in Supercritical Water Nuclear Reactor Conditions

Quantification of SCC mechanisms in austenitic alloys under PWR primary water conditions

Influence of Strain Amplitude on Low-Cycle Fatigue Behaviors of a Fourth-Generation Ni-Based Single-Crystal Superalloy at 980 °C

Stress Corrosion Cracking of High-Strength Ni-Base Alloys in PWR Primary Water Containing KOH vs. LiOH

Correlating oxidation resistance to stress corrosion cracking of 309L and 308L stainless steel claddings in simulated PWR primary water

Intergranular precipitation behavior and its influence on the stress relaxation cracking susceptibility of Super304H austenitic stainless steel weld metal during long-term aging

Effect of material chemical composition on oxidation and stress corrosion cracking of the submerged arc welding Alloy 52M overlay in a simulated PWR primary water

Stress corrosion crack propagation affected by microstructures for nuclear steam turbine rotor steels in the simulated environment

Effect of Static Mechanical Load on Intergranular Stress-Corrosion Cracking of 7050-T7451 C-Ring Specimens

Analysis of Stress Corrosion Cracking Growth Rate in the Heat-Affected Zone of 316L Based on the Heterogeneity of the Mechanical Properties

Effect of zinc injection on mitigating stress corrosion cracking initiation of structural materials in light water reactor primary water

The Effect of Strain Rate on the Tensile Deformation Behavior of Single Crystal, Ni-Based Superalloys