Abstract:The effects of surface state and applied stress on the stress corrosion cracking (SCC) behaviors of thermally treated (TT) Alloy 690 in 10 wt% NaOH solution with 100 mg/L litharge at 330 degrees C were investigated using C-ring samples with four kinds of surface states and two different stress levels. Sample outer surfaces of the first three kinds were ground to 400 grit (ground), shot-peened (SP) and electro-polished (EP) and the last one was used as the as-received state. Two samples of every kind were stressed to 100% and 200% yield stress of Alloy 690TT, respectively. The results showed that the oxide film consisted of three layers whereas continuous layer rich in Cr was not found. The poor adhesive ability indicated that the oxide film could not protect the matrix from further corrosion. Lead was found in the oxide film and the oxides at the crack paths and accelerated the dissolution of thermodynamically unstable Cr in these locations and also in the matrix. The crack initiation and propagation on Alloy 690TT were effectively retarded by SP and EP treatments but were enhanced by grinding treatment, compared with the cracks on the as-received surface. The cracking severity was also enhanced by increasing the externally applied stress. The accelerated dissolution of Cr and the local tensile stress concentration in the near-surface layer caused by cold-working and higher applied stress reduced the SCC-resistance of Alloy 690TT in the studied solution.

Effect of Static Mechanical Load on Intergranular Stress-Corrosion Cracking of 7050-T7451 C-Ring Specimens

Effects of Microstructure on the Stress Corrosion Cracking Behavior of Nickel-Aluminum Bronze Alloy in 3.5% NaCl Solution

A Three-Dimensional Model of Non-Slipping Stress Corrosion Cracking under Low Loads

The Effects of Grain Boundary Carbide Density and Strain Rate on the Stress Corrosion Cracking Behavior of Cold Rolled Alloy 690

Effect of Solution Treatment on the Fatigue Behavior of an As-Forged Mg-Zn-Y-Zr Alloy

The single effect of microstructure, residual strain and geometric structure on the stress corrosion cracking behavior of scratched alloy 690TT

Effect of Grain Structure on the Stress Corrosion Cracking (SCC) Behavior of an As-Extruded Mg-Zn-Zr Alloy

The Localized Corrosion and Stress Corrosion Cracking of a 6005A-T6 Extrusion Profile

Investigations on the SCC initiation behavior of cold worked 316 L in high temperature oxygenated water at constant loads

Investigation of Stress Corrosion Cracking Behaviors of an AZ91 Magnesium Alloy in 0.1 Kmol/m 3 Na2SO4 Solution Using Slow Strain Rate Test

A Primary Study of the Effect of Hydrostatic Pressure on Stress Corrosion Cracking of Ti-6Al-4V Alloy in 3.5% NaCl Solution

Influence of Phase Dissolution and Hydrogen Absorption on the Stress Corrosion Cracking Behavior of Mg-7%Gd-5%Y-1%Nd-0.5%Zr Alloy in 3.5 Wt.% NaCl Solution

Stress Corrosion Cracking at Low Loads: Surface Slip and Crystallographic Analysis

Effect of surface nanocrystallization induced by mechanical grinding treatment on stress corrosion cracking behavior of 316 L austenitic stainless steel in boiling MgCl 2 solution

Stress Corrosion Behavior of T91 Steel in Static Lead–bismuth Eutectic at 480 °C

Stress Corrosion Cracking of 316l Haz for 316l Stainless Steel/Inconel 52m Dissimilar Metal Weld Joint in Simulated Primary Water

Strain Rate Dependence of the Effect of Intergranular Carbides on the Resistance to Stress Corrosion Cracking Initiation of Alloy 690 in Simulated Pwr Primary Water

Effects of Surface State and Applied Stress on Stress Corrosion Cracking of Alloy 690TT in Lead-containing Caustic Solution

Synergistic Effects of Corrosion and Slow Strain Rate Loading on the Mechanical and Electrochemical Response of an Aluminium Alloy

Investigations on the SCC initiation behavior of cold worked 316L in high temperature oxygenated water at constant loads

An Investigation of Corrosion-Induced Stress During SCC