Abstract:The increasing demand for multi-band applications, including the 5G (FR1 and FR2), 6G, and WiFi, covers a frequency range from 0.45 to 40GHz. To meet specific requirements of different standards, various wideband receivers are developed [1]–[3]. In [1] and [2], the harmonic selection technique and wideband LNA are introduced to achieve wideband receiver covering the 5G FR2 band, respectively. However, to satisfy the sub-6G operation, the receiver covering the 0.45-6GHz is required, which desires a high $\mathrm{f}_{\text{high}}/\mathrm{f}_{\text{low}}$ ratio of 13.3 and is not easy to implement using on-chip transformer-based matching. Then, the resistive-load method is used for the high $\mathrm{f}_{\text{high}}/\mathrm{f}_{\text{low}}$ receiver design [3]. In this way, a 0.4-6GHz receiver is achieved. However, the mm-wave band performance is limited by the circuit parasitic. To cover both the mm-wave band and sub-6G, numerous receiver channels are used [4]. As shown in Fig. 1, the communication band selection is implemented by the SPNT on RF path, which increases the NF. Besides, a wideband LO coverage range is required, which increases the power consumption of the LO generation network. This work introduces a 0.3-40GHz hybrid-path band-selection receiver. The receiver supports 40MHz and 50MHz 4096-QAM modulation at 2.4 and 3.5GHz, while a 1.2GHz 64-QAM modulation at 18GHz is achieved. The receiver also achieves the 400MHz 256-QAM at 24, 28, 37, and 39GHz, respectively.

Analysis and Design of a 0.9 V 1 GHz-BW 14.6 Dbm-Oip3 Broadband Receiver with Current-Mode Analog Baseband in 12 Nm FinFET CMOS

A 0.9V 1.2GHz-BW 15.8dBm-OIP3 Current Mode Analog Baseband for Broadband Receivers in 12nm FinFET CMOS.

A C-Band Four-Channel Receiver with Current-Sharing and Large-Signal Multigated-Transistor Techniques in 65-Nm CMOS

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

A Sub-GHz Low-Power Receiver Employing Resistive-Feedback-Tuned LNA with 2.1-Db NF and 106-Db Gain Tuning Range

Design of a Low Power 60ghz OOK Receiver in 65nm CMOS Technology

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

A 0.6-V Zero-IF/Low-IF Receiver with Integrated Fractional-N Synthesizer for 2.4-Ghz ISM-Band Applications.

Analysis and Design of Ultra-Wideband Low-Noise Amplifier with Input/Output Bandwidth Optimization and Single-Ended/Differential-Input Reconfigurability.

A 100mhz-2ghz Wireless Receiver In 40-Nm Cmos For Software-Defined Radio

Analysis and Design of a 0.6- to 10.5-GHz LNTA for Wideband Receivers

A 0.1∼4GHz receiver and 0.1∼6GHz transmitter with reconfigurable 10∼100MHz signal bandwidth in 65nm CMOS

A 0.07–3 GHz Wideband Front-End for SDR Receiver with 2.3 Db NF and 12 Dbm IIP<sub>3</sub> in 65 Nm CMOS

A 0.1 Similar To 4ghz Receiver And 0.1 Similar To 6ghz Transmitter With Reconfigurable 10 Similar To 100mhz Signal Bandwidth In 65nm Cmos

A 600 MHz-BW 154.3 Db-Fom Current-Mode Continuous-Time Pipelined ADC in 12 Nm CMOS

A 31mA CMOS wideband BD-II B2&B3 mode receiver with 55dB gain dynamic range

Cmos Low-Power Analogue Baseband Circuits for a Non-Coherent Low Data Rate IR-UWB Receiver

A 6-7 GHz, 40 Db Receiver RF Front-End with 4.5 Db Minimum Noise Figure in 0.13μm CMOS for IR-UWB Applications

Analysis and Design of a 1.8–2.7 GHz Tunable 8-Band TDD LTE Receiver Front-End

0.6–3-Ghz Wideband Receiver RF Front-End with a Feedforward Noise and Distortion Cancellation Resistive-Feedback LNA

A -10.1Dbm IIP3, 0.3-40Ghz Receiver Using Hybrid-Path Band-Selection with Reduced LO Coverage Bandwidth Supporting 480mb/s 4096-QAM and 7.2gb/s 64-QAM Modulation