Abstract:With the development of wireless communication and Internet-of-Things (IoT), many new communication protocol standards have emerged. IoT micro-hub, which acts as the bridge between ubiquitously deployed IoT terminals and the Internet, is becoming a critical part of IoT [1]. RF transceivers for IoT micro-hub applications are now facing several technical challenges. Firstly, they should be highly re-configurable and flexible to be compatible with a variety of IoT communication protocols. In addition, for long communication distance and complex communication scenarios, there also exists demand to integrate an on-chip power amplifier (PA) into the RF transceiver to reduce cost. Secondly, the number of IoT micro-hubs has increased dramatically with the development of IoT. For lower cost and longer lifetime, there is strong demand to reduce power consumption and chip area of these RF transceivers. A possible solution for IoT micro-hub applications is the software-defined-radio (SDR) transceivers [2]–[4]. However, the high power consumption and large chip area make them not suitable for IoT micro-hub applications. A 0.1-4GHz receiver and 0.1-6GHz transmitter for SDR applications is proposed in [2], but the carrier frequency of receiver is limited to 0.1-4GHz and the noise Figure (NF) is 3-8dB. Though not integrating a phase-locked loop (PLL) or a PA, the chip occupies $8.12\mathrm{mm}^{2}$. A multi-standard transceiver is proposed in [4], in which four parallel low noise amplifiers (LNAs) with several inductors are used in the receiver to cover 0.1-6GHz band, which occupy considerable chip area.

A 100mhz-2ghz Wireless Receiver In 40-Nm Cmos For Software-Defined Radio

Wideband Receiver for Software Defined Radio in GHz Range Using Standard 40nm CMOS Technology

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A 1.2V 0.1&#x2013;3ghz Software-Defined Radio Receiver Front-End in 130nm CMOS

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

Design of a Low Power 60ghz OOK Receiver in 65nm CMOS Technology

A 0.1–4 GHz SDR receiver with reconfigurable 10–100 MHz signal bandwidth in 65 nm CMOS

A 11 Mw 2.4 GHz 0.18 Μm CMOS Transceivers for Wireless Sensor Networks

A 12-Mw 40–60-Ghz 0.18- $\mu {\hbox {m}}$ BiCMOS Oscillator-Less Self-Demodulator for Short-Range Software-Defined Transceivers

Low power high data rate GHz range receiver in 40nm CMOS technology

Implementation of a New S-Band Micro-Transponder Based on Software Defined Radio

A 90-98-ghz FMCW Radar Transceiver Supporting Broadband Modulation in 65nm CMOS

A 0.1–5ghz Flexible SDR Receiver in 65nm CMOS

A 0.1&#x2013;2 GHz CMOS RF Front-End for Software-Defined Radio Applications

A 0.07–3 GHz Wideband Front-End for SDR Receiver with 2.3 Db NF and 12 Dbm IIP<sub>3</sub> in 65 Nm CMOS

An LP/CBP reconfigurable analog baseband circuit for software-defined radio receivers in 65 nm CMOS.

An mm-Wave CMOS/Si-Photonics Reconfigurable Hybrid-Integrated Heterodyning Software-Defined Radio Receiver

A wideband low noise amplifier for multi-standard receivers

A Fully Integrated 60ghz Four Channel CMOS Receiver with 7ghz Ultra-Wide Bandwidth for IEEE 802.11ad Standard

Wideband Fraction-N Frequency Synthesizer Design for Software-Defined Radio

A 2.85mm 2 RF Transceiver in 40nm CMOS for IoT Micro-Hub Applications