Abstract:This article presents a low-power (LP), compact,wideband (WB) low-noise transconductance amplifier (LNTA)-first receiver (RX) designed for software-defined radios (SDRs).It comprises the LNTA, frequency divider, mixer, and trans-impedance amplifier (TIA). The LNTA utilizes a common gate(CG)-common source (CS) structure without on-chip inductorsand incorporates gm-boosting and current reuse techniques toeffectively reduce power consumption. A novel noise-canceling(NC) strategy is proposed to break the inherent tradeoff betweeninput impedance matching, noise figure (NF), and gain. Thedivider adopts a windmill structure based onNANDgates, while25% duty-cycle quadrature clocks drive the double-balancedpassive mixer. The third-order filtering TIA is based on a three-stage pseudo-differential operational transconductance amplifier(OTA). It implementsRCand feedforward (FF) compensationtechniques to attain a 3.25-GHz unity gain loop bandwidth(BW) and 68-dB loop gain. Fabricated in a 40-nm LP CMOStechnology, the chip features 38-dB conversion gain, 50-MHzbaseband (BB) BW, 3.5-dB NF, and in-band (IB) output third-order intercept point of up to 40 dBm. The RX operates over afrequency range of 0.1-5.5 GHz. It consumes 36 mW of staticpower in the RX signal path and 15 mW of dynamic powerin the local oscillator (LO) path at 5 GHz. The core area isonly 0.1 mm(2).

A 0.07–3 GHz Wideband Front-End for SDR Receiver with 2.3 Db NF and 12 Dbm IIP<sub>3</sub> in 65 Nm CMOS

A 100mhz-2ghz Wireless Receiver In 40-Nm Cmos For Software-Defined Radio

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A 1.2V 0.1&#x2013;3ghz Software-Defined Radio Receiver Front-End in 130nm CMOS

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

A High-Linearity 7–9-Ghz Receiver Front End with Strength-Oriented Nonlinearity Cancellation

0.9–10GHz low noise amplifier with capacitive cross coupling

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

A Sub-GHz Low-Power Receiver Employing Resistive-Feedback-Tuned LNA with 2.1-Db NF and 106-Db Gain Tuning Range

A 0.6-V Zero-IF/Low-IF Receiver with Integrated Fractional-N Synthesizer for 2.4-Ghz ISM-Band Applications.

A 0.1–5ghz Flexible SDR Receiver in 65nm CMOS

A 0.1–4 GHz SDR receiver with reconfigurable 10–100 MHz signal bandwidth in 65 nm CMOS

A+21.2 Dbm Out-Of-Band Iip3 0.2-3ghz Rf Front-End Using Impedance Translation Technique

A 6-7 GHz, 40 Db Receiver RF Front-End with 4.5 Db Minimum Noise Figure in 0.13μm CMOS for IR-UWB Applications

0.6–3-Ghz Wideband Receiver RF Front-End with a Feedforward Noise and Distortion Cancellation Resistive-Feedback LNA

A 2.4ghz Low Noise High Linearity RF Front-End Design.

A 0.13µm CMOS 1.5-to-2.15ghz Low Power Transmitter Front-End for SDR Applications

A 0.13&#x03bc;m CMOS UWB Receiver Front-End Using Passive Mixer

A Low-Power, Compact, 0.1–5.5-Ghz, 40-Dbm IB OIP3 LNTA-First Receiver for SDR

A 5 Ghz 7.2 Db Nf Low Power Direct Conversion Receiver Front-End with Balun Lna

A Low Power 3–5 GHz CMOS UWB Receiver Front-End

A 0.07–3 GHz Wideband Front-End for SDR Receiver with 2.3 Db NF and 12 Dbm IIP&lt;sub&gt;3&lt;/sub&gt; in 65 Nm CMOS