Abstract:This article reports a high-gain wideband low-noise amplifier (LNA) with single ended input and differential output for multi-standard wireless receiver operating in 0.2 to 7 GHz. The proposed balun-LNA is cascode structure with common-gate–common-source (CG–CS) balun load to achieve single to differential conversion. Focusing on improving the voltage gain, bandwidth and noise performance at the same time, several techniques are implemented in this balun-LNA. A current source is added shunting CG stage to relieve voltage headroom and improve gain and linearity. Wideband input matching is achieved by active shunt-shunt resistive feedback, together with the input series inductor. Moreover, feedforward and current-reuse technique are introduced to further optimize the noise performance. The proposed LNA has a measured voltage gain of 26 dB which is nearly 6 dB higher than other balun-LNA with same supply and process. Moreover, the minimum noise figure (NF) is 2.0 dB owing to multiple noise-optimized technique. The achieved input power at 1 dB gain compression point (IP1 dB) is −14 dB m at 1 GHz and input return loss ( S11 ) is better than −10 dB across entire operating frequency range. IIP3 and IIP2 achieve −7 dBm and 25 dBm respectively, measured at 1 GHz. The power consumption is 15.5 mW at 1.2 V supply. The LNA is fabricated in 130 nm CMOS process and the active area is 0.097 mm2 . The LNA achieves high voltage gain and wide operating frequency range with low NF, which can be reflected from the figure of merit (FOM) of 23.1.

A 5 Ghz 7.2 Db Nf Low Power Direct Conversion Receiver Front-End with Balun Lna

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

A High-Linearity 7–9-Ghz Receiver Front End with Strength-Oriented Nonlinearity Cancellation

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

An Ultra-Low-power 5ghz Front End with Feedforward Body Bias LNA and Single to Double Balance Subharmonic Mixer Topology for Direct Conversion Receiver

A Sub-GHz Low-Power Receiver Employing Resistive-Feedback-Tuned LNA with 2.1-Db NF and 106-Db Gain Tuning Range

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A Low-Power Low-Noise Direct-Conversion Front-End with Digitally Assisted IIP2 Background Self Calibration

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

0.9–10GHz low noise amplifier with capacitive cross coupling

A Low Power Direct Conversion Receiver RF Front-End with High In-Band IIP2/IIP3 and Low 1/f Noise

A Low-Power Monolithic Reconfigurable Direct-Conversion Receiver RF Front-End for 802.11a/b/g Applications

An 8mw Ultra Low Power 60ghz Direct-Conversion Receiver with 55db Gain and 4.9db Noise Figure in 65nm CMOS

A Low Power 3–5 GHz CMOS UWB Receiver Front-End

A 2.1–2.5 GHz high linearity and low noise down-conversion active mixer

A low-power monolithic reconfigurable direct-conversion receiver RF front-end for 802.1 la/b/g applications

A Dual-Band Reconfigurable Direct-Conversion Receiver Rf Front-End

A high-gain wideband balun-LNA with multiple noise-optimized technique

6.7 A 1.75dB-NF 25mW 5GHz Transformer-Based Noise-Cancelling CMOS Receiver Front-End

A Low-Power 2.4-Ghz Receiver Front-End with a Complementary Series Feedback LNA and a Current-Reused Passive Down-Converter Based on Gm-Boosted TIA for WSN Applications.

A Low Power 35 Ghz Cmos Uwb Receiver Front-End