Abstract:An interference-robust reconfigurable receiver in 65-nm CMOS is presented. The front end is split into a low-band (LB) RF path (0.1-1.5 GHz) and a high-band (HB) RF path (1-5 GHz). By utilizing a harmonic recombination technique, the LB path could reject the third/fifth-order harmonic interferences. A tunable narrowband dual-feedback commongate low-noise amplifier (LNA) with LC resonant load provides second-order bandpass filtering to reject the harmonic interferences in the HB path. The RF high-Q bandpass filtering based on the voltage-mode passive mixer and the current-mode low-pass filter in the analog baseband improves the receiver's resilience to out-of-band interferences. A novel power-detectionbased automatic frequency calibration technique is proposed to calibrate the operating frequency of the LNA in the HB path and overcome the effects of process, voltage, and temperature variations. The presented receiver has been implemented in a 65-nm CMOS and consumes 20-76-mW power from 1.2-V power supplies, with a core die area of 5 mm(2). The measured results show that the receiver can tolerate -5-dBm interference with 16-dB noise figure (NF) and achieve 95-105-dB maximum conversion gain and 1.7-8-dB NF over 0.1-5 GHz. It also achieves an average harmonic rejection (HR3)/HR5 of 61/68dB, +7.1/+14.4 dBm in-band/out-of-band input third-order intercept point (OB-IIP3), +71.2-dBm OB-IIP2, and 58.1-dB-image rejection, after the digitally assisted calibrations. The system-level measurements show that the presented receiver achieves 2.1% error vector magnitude (EVM) for 850-MHz Global System for Mobile Communication signals and 5% EVM for band 42 time division duplexing-local thermal equilibrium (LTE) signals, respectively.

A Dual-Band Reconfigurable Direct-Conversion Receiver Rf Front-End

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A Low-Power Monolithic Reconfigurable Direct-Conversion Receiver RF Front-End for 802.11a/b/g Applications

A low-power monolithic reconfigurable direct-conversion receiver RF front-end for 802.1 la/b/g applications

A compact dual-band direct-conversion CMOS transceiver for 802.11a/b/g WLAN

A Low-Power Low-Noise Direct-Conversion Front-End with Digitally Assisted IIP2 Background Self Calibration

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

A Sub-GHz Low-Power Receiver Employing Resistive-Feedback-Tuned LNA with 2.1-Db NF and 106-Db Gain Tuning Range

A Low Power Direct Conversion Receiver RF Front-End with High In-Band IIP2/IIP3 and Low 1/f Noise

A 28-/60-GHz Dual-Band Receiver Front-End With Sideband-Selection Technique in 65-nm CMOS

A 1 GHz CMOS RF front-end IC for a direct-conversion wireless receiver

A 2.1–2.5 GHz high linearity and low noise down-conversion active mixer

A 5 Ghz 7.2 Db Nf Low Power Direct Conversion Receiver Front-End with Balun Lna

An Ultra-Low-power 5ghz Front End with Feedforward Body Bias LNA and Single to Double Balance Subharmonic Mixer Topology for Direct Conversion Receiver

A Direct Conversion WLAN Receiver

An Interference-Robust Reconfigurable Receiver with Automatic Frequency-Calibrated LNA in 65-Nm CMOS

An Optimized Receiver RF Front-End

A+21.2 Dbm Out-Of-Band Iip3 0.2-3ghz Rf Front-End Using Impedance Translation Technique

A Low-Power 2.4-Ghz Receiver Front-End with a Complementary Series Feedback LNA and a Current-Reused Passive Down-Converter Based on Gm-Boosted TIA for WSN Applications.

A Direct Conversion WiMAX RF Receiver Front-End in CMOS Technology