Abstract:An interference-robust reconfigurable receiver in 65-nm CMOS is presented. The front end is split into a low-band (LB) RF path (0.1-1.5 GHz) and a high-band (HB) RF path (1-5 GHz). By utilizing a harmonic recombination technique, the LB path could reject the third/fifth-order harmonic interferences. A tunable narrowband dual-feedback commongate low-noise amplifier (LNA) with LC resonant load provides second-order bandpass filtering to reject the harmonic interferences in the HB path. The RF high-Q bandpass filtering based on the voltage-mode passive mixer and the current-mode low-pass filter in the analog baseband improves the receiver's resilience to out-of-band interferences. A novel power-detectionbased automatic frequency calibration technique is proposed to calibrate the operating frequency of the LNA in the HB path and overcome the effects of process, voltage, and temperature variations. The presented receiver has been implemented in a 65-nm CMOS and consumes 20-76-mW power from 1.2-V power supplies, with a core die area of 5 mm(2). The measured results show that the receiver can tolerate -5-dBm interference with 16-dB noise figure (NF) and achieve 95-105-dB maximum conversion gain and 1.7-8-dB NF over 0.1-5 GHz. It also achieves an average harmonic rejection (HR3)/HR5 of 61/68dB, +7.1/+14.4 dBm in-band/out-of-band input third-order intercept point (OB-IIP3), +71.2-dBm OB-IIP2, and 58.1-dB-image rejection, after the digitally assisted calibrations. The system-level measurements show that the presented receiver achieves 2.1% error vector magnitude (EVM) for 850-MHz Global System for Mobile Communication signals and 5% EVM for band 42 time division duplexing-local thermal equilibrium (LTE) signals, respectively.

A Low-Power Monolithic Reconfigurable Direct-Conversion Receiver RF Front-End for 802.11a/b/g Applications

A low-power monolithic reconfigurable direct-conversion receiver RF front-end for 802.1 la/b/g applications

A compact dual-band direct-conversion CMOS transceiver for 802.11a/b/g WLAN

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A Dual-Band Reconfigurable Direct-Conversion Receiver Rf Front-End

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

Design of a Direct-conversion IEEE 802.11b/g WLAN Receiver RF Front-end

A 5 Ghz 7.2 Db Nf Low Power Direct Conversion Receiver Front-End with Balun Lna

A Low Noise, High Linearity CMOS Receiver for 802. 11b WLAN Applications

A Differential Low-Voltage High Gain Current-Mode Integrated RF Receiver Front-End

A 2.4-Ghz CMOS Monolithic Transceiver Front-End for IEEE 802.11b Wireless LAN Applications

A Low Voltage CMOS RF Front-End for IEEE 802.11b WLAN Transceiver

A Fully Integrated Reconfigurable Low-Power Sub-GHz Transceiver for 802.11ah in 65nm CMOS

A 28-/60-GHz Dual-Band Receiver Front-End With Sideband-Selection Technique in 65-nm CMOS

A Low Power Direct Conversion Receiver RF Front-End with High In-Band IIP2/IIP3 and Low 1/f Noise

A Low-Power 2.4-GHz Receiver Front End With a Lateral Current-Reusing Technique

An Interference-Robust Reconfigurable Receiver with Automatic Frequency-Calibrated LNA in 65-Nm CMOS

A Low-Power 2.4-Ghz Receiver Front-End with a Complementary Series Feedback LNA and a Current-Reused Passive Down-Converter Based on Gm-Boosted TIA for WSN Applications.

A 0.1–1 GHz Low Power RF Receiver Front-End with Noise Cancellation Technique for WSN Applications

An Ultra-Low-power 5ghz Front End with Feedforward Body Bias LNA and Single to Double Balance Subharmonic Mixer Topology for Direct Conversion Receiver