Abstract:Direct conversion receiver (DCR) architecture is a promising candidate in the radio frequency (RF) front end because of its low power consumption, low cost and ease of integration. However, flicker noise and direct current (DC) offset are large issues. Owing to the local oscillator (LO) frequency, which is half of the RF frequency, and the absence of a DC bias current that introduces no flicker noise, the subharmonic passive mixer (SHPM) core topology front end overcomes the shortcoming effectively. When more and more receivers (RX) and transmitters (TX) are integrated into one chip, the linearity of the receiver front end becomes a very important performer that handles the TX and RX feedthrough. Another reason for the requirement of good linearity is the massive electromagnetic interference that exists in the atmosphere. This paper presents a linearity-improved RF front end with a feedforward body bias (FBB) subharmonic mixer core topology that satisfies modern RF front end demands. A novel complementary derivative superposition (DS) method is presented in low noise amplifier (LNA) design to cancel both the third- and second-order nonlinearities. To the best knowledge of the authors, this is the first time FBB technology is used in the SHPM core to improve linearity. A Volterra series is introduced to provide an analytical formula for the FBB of the SHPM core. The design was fabricated in a 0.13 μm complementary metal oxide semiconductor (CMOS) process with a chip area of 750 μm × 1270 μm. At a 2.4 GHz working frequency, the measurement result shows a conversion gain of 36 dB, double side band (DSB) noise figure (NF) of 6.8 dB, third-order intermodulation intercept point (IIP3) of 2 dBm, LO–RF isolation of 90 dB and 0.8 mW DC offset with 14.4 mW power consumption at 1.2 V supply voltage. These results exhibit better LO–RF feedthrough and DC offset, good gain and NF, moderate IIP3 and the highest figure of merit compared to the state-of-the-art publications.

An Ultra-Low-power 5ghz Front End with Feedforward Body Bias LNA and Single to Double Balance Subharmonic Mixer Topology for Direct Conversion Receiver

A High Performance 2-Ghz Direct-Conversion Front End with Single-Ended RF Input in 0.13 Um CMOS

A 5 Ghz 7.2 Db Nf Low Power Direct Conversion Receiver Front-End with Balun Lna

A Sub-GHz Low-Power Receiver Employing Resistive-Feedback-Tuned LNA with 2.1-Db NF and 106-Db Gain Tuning Range

A 27 - 57 GHz Down-conversion Mixer with Bulk Injection Technique

A Sub-GHz CMOS Low-IF Receiver for Lot Applications

A Sub-1-GHz Band High-Dynamic-Range Receiver with Integrated Self-Adaptive Multipart AGC Loops

A 0.5-8Ghz Reconfigurable CMOS RF Receiver Front-end for CR and DPA Applications

A 0.1-1.9Ghz 65nm CMOS Variable-Gain Mixer-First Receiver with DSA and Noise-Shaping TIA.

An Ultra-Low Power K band Balanced Frequency Doubler with a Novel Current-reused Structure

A Linearity Improvement Front End with Subharmonic Current Commutating Passive Mixer for 2.4 GHz Direct Conversion Receiver in 0.13 Μm CMOS Technology

A 2.1–2.5 GHz high linearity and low noise down-conversion active mixer

An 8mw Ultra Low Power 60ghz Direct-Conversion Receiver with 55db Gain and 4.9db Noise Figure in 65nm CMOS

A Low Power Direct Conversion Receiver RF Front-End with High In-Band IIP2/IIP3 and Low 1/f Noise

A Dual-Band Reconfigurable Direct-Conversion Receiver Rf Front-End

A CMOS Self-Mixing-free Front-End for Direct Conversion Applications

Design of Ultra-Low-Power 60-Ghz Direct-Conversion Receivers in 65-Nm CMOS

A Low-Power Monolithic Reconfigurable Direct-Conversion Receiver RF Front-End for 802.11a/b/g Applications

A Low-Power 2.4-Ghz Receiver Front-End with a Complementary Series Feedback LNA and a Current-Reused Passive Down-Converter Based on Gm-Boosted TIA for WSN Applications.

An Optimized Receiver RF Front-End

A Low Power 3–5 GHz CMOS UWB Receiver Front-End