Abstract:Yield stress, as well as ultimate stress, decreases with an increased temperature. A much smaller cutting force can be applied to perform the machining at high temperatures. Material is considered "softened" when its yield and ultimate stresses decrease due to the increase of temperature. During the hybrid laser-waterjet micromachining process, the material is heated by laser. Once the critical resolved shear stress (CRSS), related to the yield stress, decreases to be equal to the applied resolved shear stress induced by the pressurized waterjet impingement, the material begins to be deformed and then removed plastically. The hybrid laser-waterjet micromachining technology shows a satisfying performance on almost damage-free and high-efficient micromachining of thermalsensitive and hard-brittle materials at their "softened" status. The present study is focused on the material removal mechanism of single crystal 4H-SiC in the hybrid laser-waterjet micromachining process. The temperature-dependent CRSS on the primary slip system of 4H-SiC is formulated. It is shown that the CRSS of 4H-SiC is less than 5 MPa at 1650 K. The shear stress induced by pressurized waterjet impingement, laser heating effect under the laser-water interference and the waterjet cooling effect are respectively studied. The range of water pressure used in the machining process is from 4 MPa to 13 MPa. A 2-D numerical model is developed using the finite difference method (FDM). The simulations show that the material begins to be removed before the laser intensity reaches its maximum in a laser pulse cycle. The depth and width of the microgroove increase gradually in the following several cycles. The increments become gradually less until this increase stops. The material is removed before it's heated to its melting temperature and at a softened but still solid status. Heat accumulation between laser pulses is not expected in the process. The machined surface quality and material removal mechanisms of the hybrid laser-waterjet micromachining and laser dry ablation are compared by 3D profiles and SEM photographs of the microgrooves obtained from these two machining methods. The surface quality obtained from hybrid laser-waterjet micromachining is better than that obtained from laser dry ablation. The protrusion strips along the cut edges of laser dry ablation are scaly and similar to welded junction. It indicates that the material is melted or vaporized by laser heating and re-solidified at cut edges to form a recast layer during laser dry ablation. There aren't recast layers on the machined surface of hybrid laser-waterjet micromachining. Its surface texture is characterized as a typical feature of plastic slip.

Surface Integrity Analysis of Si3N4 under Cryogenic Assisted Femtosecond Laser Ablation

Investigation of mechanism and surface morphology on the femtosecond laser ablation of silicon nitride under different auxiliary processing environments

Ablation Threshold and Material Removal Mechanisms of SiC Processed by Femtosecond Laser

Crystal Cleavage, Periodic Nanostructure And Surface Modification Of Sic Ablated By Femtosecond Laser In Different Media

Investigations on the ablation behavior of C/SiC under femtosecond laser

Experimental Investigation on Laser In-Situ Assisted Ultra-Precision Cutting of Fused Silica

Influence of surface morphology on processing of C/SiC composites via femtosecond laser

Experimental Investigation on Ablation of 4H-SiC by Infrared Femtosecond Laser

Thermal analysis of in-situ laser assisted diamond cutting of fused silica and process optimization

Centimeter-scale low-damage micromachining on single-crystal 4H–SiC substrates using a femtosecond laser with square-shaped Flat-Top focus spots

Femtosecond laser surface modification of 4H-SiC improves machinability

Thermal Effects on Removal Mechanism of Monocrystal SiC During Micro-Laser Assisted Nanogrinding Process

Material Removal of Single Crystal 4H-Sic Wafers in Hybrid Laser-Waterjet Micromachining Process

Study of Femtosecond Laser Ablation and Polishing Process on 4H-SiC Substrate

Study of Femtosecond Laser Ablation Effect on Micro-Processing for 4H-SiC Substrate

Cryogenic assisted femtosecond laser ablation of polycrystalline diamond

Experimental and Simulation Research on Femtosecond Laser Induced Controllable Morphology of Monocrystalline SiC

Numerical Investigation on Subsurface Damage in Nanometric Cutting of Single-Crystal Silicon at Elevated Temperatures

Experimental investigations on the laser-assisted machining of single crystal Si for optimal machining

Microstructure evolution and ablation mechanism of SiCf/SiC ceramic matrix composite microgrooves processed by pico-second laser

Investigation on femtosecond laser combined with dynamic wet etching machining of SiC/SiC