Abstract:Plasma etching with high selectivity and anisotropy for 20 nm poly-Si gate patterning on EOT of 1.4 nm gate oxynitride is developed in a Cl2/HBr/O2 gas mixture successfully. Direct write e-beam lithography is used for an SAL601 chemically amplified negative resist pattern. Using a combination of resist ashing and TEOS hard mask trimming process, sub-25 nm TEOS SiO2 mask patterns are obtained in the control. Various gas mixtures based on Cl2, HBr, and O2 have been used to study the etching characteristics of poly-Si on EOT of 1.4 nm gate oxynitride. The O2 content as well as HBr are very sensitive to etch rate, selectivity, and the protection of the sidewalls of polysilicon, owing to SiO2-like film, SiOxBry, formed on the etched surface confirmed by x-ray photoelectron spectroscopy. And the ratio of Cl2/HBr/O2 in gas mixture is also tightly related to the etching profile. Using a four-step etching process under optimum conditions the selectivity of poly-Si to oxide is much higher than 500:1, in fact, after polysilicon etching the net deposition of oxide is observed, and no damage on the active area beside the gates for EOT of 1.4 nm gate oxide is observed, too. The etching profile of the 20 nm poly-Si gate pattern is perfectly vertical and an overall narrowing by an estimated 5 nm is observed for oxide masked poly-Si gate etching. The possible mechanism is discussed. This etching process combined with resist ashing and the TEOS hard mask trimming process are implemented successfully to the fabrication of high performance 36 nm gate length complementary metal–oxide–semiconductor (CMOS) devices and 42 nm gate length 32 frequency dividers with 57 stage/201 stage CMOS ring oscillators embedded, the EOT of gate oxynitrid is 1.4 nm, and very good results are obtained.

Gate Oxide Punching Thru Mechanism in Plasma Dry Etching

Optimization of Polysilicon Gate Etching Process in SONOS Memory Fabrication

Research on Integrated Trench Etching for Trench-Type Power MOSFET

20 Nm Polysilicon Gate Patterning and Application in 36 Nm Complementary Metal–oxide–semiconductor Devices

Reduction of silicon recess caused by plasma oxidation during high-density plasma polysilicon gate etching

Increased hole trapping in gate oxides as latent damage from plasma charging

Mechanism of Plasma Charging Damage on Ultrathin Gate Oxide

High Mobility Ge CMOS Devices with Ultrathin EOT Gate Stacks Fabricated by Plasma Post Oxidation

Top-Gate Dry-Etching Patterned Polymer Thin-Film Transistors with a Protective Layer on Top of the Channel

Optimized Work Function Metal Layer Damage Effect in Metal Gate BARC Etch Process by ICP Etch System

Study of Selective Dry Etching Effects of 15-Cycle Si0.7Ge0.3/Si Multilayer Structure in Gate-All-Around Transistor Process

Reducing damage to Si substrates during gate etching processes by synchronous plasma pulsing

Cause of Etch Pits during the High Speed Plasma Etching of Silicon Carbide and an Approach to Reduce their Size

Edge hole direct tunneling leakage in ultrathin gate oxide p-channel MOSFETs

Gate Leakage for 28 Nm Stacked HfZrO X Dielectric of P-Channel MOSFETs after Decoupled Plasma Nitridation Treatment with Annealing Temperatures

Gate Dielectric Leakage Reduction in Hard-Mask Defined and Dry-Etch Patterned Organic TFTs Devices

Gate Oxide Reliability Degradation by Post Poly-Silicon Annealing and Suppression Method

Effects of Etching Residue on Positive Shift of Threshold Voltage in Amorphous Indium–Zinc-Oxide Thin-Film Transistors Based on Back-Channel-Etch Structure

Wet-Etch Method for Patterning Metal Electrodes Directly on Amorphous Oxide Semiconductor Films

P‐1.14: the Influence of Bottom Gate Dielectric Roughness on the Performance of Double‐Gate A‐igzo Thin Film Transistors

Study on Ultra-Thin Gate Dielectrics: Surface Preparation and Reliability