Abstract:The 3D tri-gate FinFET device architecture is a key transistor scaling to 22nm node and beyond for its excellent short-channel performance[1]. However, compared with planar transistors, it poses greater challenge in the finFET gate etch.[2] As shown in fig.1, the etch needs to stop on top of the fin while etching further down to the STI oxide layer. Therefore, the top of fin needs to endure long time over etch without any structural damage which would adversely affect device performance. What’s more, the gate profile must be vertical and there should not be residual in the corner of gate and fin. It is not an easy task to achieve, at the same time, the three goals of vertical gate profile, no residual in the corner of fin and gate, as well as no structure damage on the top of fin, due to an unavoidable tradeoff. More specifically, vertical gate profile and no residual in the corner of fin demand strong etch function and light polymer, while no structure damage in the top of fin requires weak etch function and heavy polymer, which points to high etch selectivity of silicon to oxide layer. To achieve good etch results, one often falls into this dilemma. As far as we know, few publicly available papers have provided satisfactory solutions to the above- mentioned problem. In this work, we deal with it. The process of gate stack with CD below 30nm is illustrated in fig.2. Then, a HBr/O2 process in transformer coupled plasma is applied to finFET gate etch. As shown in fig.3, gate profile is vertical, fin is well protected and no residual appears in the corner fin. In conclusion, an HBr/O2 plasma etch process of finFET gate with CD below 30nm is investigated.Through appropriate tradeoff , an etch result of vertical gate profile, no residual in the sidewall and corner of fin, no structure damage on the top of fin is achieved.

Research on Integrated Trench Etching for Trench-Type Power MOSFET

Research Progress in Ge-based Advanced Field Effect Transistor Technology

Annealing Process on MOS channel Properties for Quasi‐Vertical GaN‐on‐Sapphire Trench MOSFET

Evaluation of Trench Oxide Protection Techniques on Ultra High Voltage (10 kV) 4H-SiC UMOSFETs

Ge CMOS Technology with Advanced Interface and Junction Engineering.

Demonstrating SiC In Situ Rounded Trench Processing Technologies for Future Power Trench MOSFET Applications

Metal hard-mask based AIO etch challenges and solutions

A Novel Atomic-Level Post-Etch-Surface-Reinforcement Process for High-Performance p-GaN Gate HEMTs Fabrication

Fabrication and Optimization of a High Speed Deep-Trench Super-Junction MOSFET with Improved EMI Performance

Fabrication and selective wet etching of Si0.2Ge0.8/Ge multilayer for Si0.2Ge0.8 channel gate-all-around MOSFETs

Parametric Study, Modeling of Etching Process and Application for Tapered Through-Silicon-via

Post-trench restoration for vertical GaN power devices

Finfet Gate Etch Towards 16nm Node CMOS Technology

Micro-trench free 4H-SiC etching with improved SiC/SiO2 selectivity using inductively coupled SF6/O2/Ar plasma

Design and Process Analysis of a Split-Gate Trench Power MOSFET with Bottom-Trench Hk-Pillar Superjunction for Enhanced Performance

Influence of Different Device Structures on the Degradation for Trench-Gate SiC MOSFETs: Taking Avalanche Stress as an Example

Review on the Reliability Mechanisms of SiC Power MOSFETs: A Comparison between Planar-Gate and Trench-Gate Structures

A New Shallow Trench and Planar Gate Mosfet Structure Based on Vdmos Technology

4H-Sic Trench Gate Lateral MOSFET with Dual Source Trenches for Improved Performance and Reliability

Investigation of Power MOSFET with Strained SiGe Channel

Improved Subthreshold Characteristics of Epi-Silicon FinFET via Fin Surface Passivation Technologies