Abstract:Abstract Wet anisotropic etching is extensively employed in silicon bulk micromachining to fabricate microstructures for various applications in the field of microelectromechanical systems (MEMS). In addition, it is most widely used for surface texturing to minimize the reflectance of light to improve the efficiency of crystalline silicon solar cells. In wet bulk micromachining, the etch rate is a major factor that affects the throughput. Slower etch rate increases the fabrication time and therefore is of great concern in MEMS industry where wet anisotropic etching is employed to perform the silicon bulk micromachining, especially to fabricate deep cavities and freestanding microstructures by removal of underneath material through undercutting process. Several methods have been proposed to increase the etch rate of silicon in wet anisotropic etchants either by physical means (e.g. agitation, microwave irradiation) or chemically by incorporation of additives. The ultrasonic agitation during etching and microwave irradiation on the etchants increase the etch rate. However, ultrasonic method may rupture the fragile structures and microwave irradiation causes irradiation damage to the structures. Another method is to increase the etching temperature towards the boiling point of the etchant. The etching characteristics of pure potassium hydroxide solution (KOH) is studied near the boiling point of KOH, while surfactant added tetramethylammonium hydroxide (TMAH) is investigated at higher temperature to increase the etch rate. Both these studies have shown a potential way of increasing the etch rate by elevating the temperature of the etchants to its boiling point, which is a function of concentration of etch solution. The effect of various kinds of additives on the etch rate of silicon is investigated in TMAH and KOH. In this paper, the additives which improve the etch rate have been discussed. Recently the effect of hydroxylamine (NH 2 OH) on the etching characteristics of TMAH and KOH is investigated in detail. The concentration of NH 2 OH in TMAH/KOH is varied to optimize the etchant composition to obtain improved etching characteristics especially the etch rate and undercutting which are important parameters for increasing throughput. In this article, different methods explored to improve the etch rate of silicon have been discussed so that the researchers/scientists/engineers can get the details of these methods in a single reference.

Cause of Etch Pits during the High Speed Plasma Etching of Silicon Carbide and an Approach to Reduce their Size

Isotropic Etch for SiO2 Microcantilever Release with ICP System

High-etch rate processes for performing deep, highly anisotropic etches in silicon carbide using inductively coupled plasma etching

Producing Silicon Carbide Micro and Nanostructures by Plasma‐Free Metal‐Assisted Chemical Etching

Fabrication of ultrathin and highly uniform silicon on insulator by numerically controlled plasma chemical vaporization machining

Surface Modification of Silicon Carbide Wafers Using Atmospheric Plasma Etching: Effects of Processing Parameters

A study on the etching characteristics of atmospheric pressure plasma for single-crystal silicon wafer

Effect of process parameters on sidewall damage in deep silicon etch

Reduction of silicon recess caused by plasma oxidation during high-density plasma polysilicon gate etching

Wafer level microarcing model in 90nm chemical-vapor deposition low-k via etch on 300mm silicon-on-insulator substrate

Microscale pattern etch of 4H–SiC by inductively coupled plasma

Sub-damage-threshold plasma etching and profile tailoring of Si through laser-stimulated thermal desorption

Research on Silicon Wafer Surface Phase under the Ultra-thin Slicing Process and Its Etching Hindrance Behavior during Metal-Assisted Chemical Etching

High speed silicon wet anisotropic etching for applications in bulk micromachining: a review

Remote Plasma Enhanced Cyclic Etching of a Cyclosiloxane Polymer Thin Film

Plasma Induced Damage Reduction of Ultra Low-k Dielectric by Using Source Pulsed Plasma Etching for Next BEOL Interconnect Manufacturing

Pseudo‐Wet Plasma Mechanism Enabling High‐Throughput Dry Etching of SiO2 by Cryogenic‐Assisted Surface Reactions

Correlation and Interaction between Sidewall Passivation and Chamber Walls Deposition During Silicon Gate Etching

Study on the photoelectrochemical etching process of semiconducting 6H–SiC wafer

Negative charge injection to a positively charged SiO2 hole exposed to plasma etching in a pulsed two-frequency capacitively coupled plasma in CF4/Ar

Low-temperature plasma etching of high aspect-ratio densely packed 15 to sub-10 nm silicon features derived from PS-PDMS block copolymer patterns