Abstract:Abstract Wet anisotropic etching is extensively employed in silicon bulk micromachining to fabricate microstructures for various applications in the field of microelectromechanical systems (MEMS). In addition, it is most widely used for surface texturing to minimize the reflectance of light to improve the efficiency of crystalline silicon solar cells. In wet bulk micromachining, the etch rate is a major factor that affects the throughput. Slower etch rate increases the fabrication time and therefore is of great concern in MEMS industry where wet anisotropic etching is employed to perform the silicon bulk micromachining, especially to fabricate deep cavities and freestanding microstructures by removal of underneath material through undercutting process. Several methods have been proposed to increase the etch rate of silicon in wet anisotropic etchants either by physical means (e.g. agitation, microwave irradiation) or chemically by incorporation of additives. The ultrasonic agitation during etching and microwave irradiation on the etchants increase the etch rate. However, ultrasonic method may rupture the fragile structures and microwave irradiation causes irradiation damage to the structures. Another method is to increase the etching temperature towards the boiling point of the etchant. The etching characteristics of pure potassium hydroxide solution (KOH) is studied near the boiling point of KOH, while surfactant added tetramethylammonium hydroxide (TMAH) is investigated at higher temperature to increase the etch rate. Both these studies have shown a potential way of increasing the etch rate by elevating the temperature of the etchants to its boiling point, which is a function of concentration of etch solution. The effect of various kinds of additives on the etch rate of silicon is investigated in TMAH and KOH. In this paper, the additives which improve the etch rate have been discussed. Recently the effect of hydroxylamine (NH 2 OH) on the etching characteristics of TMAH and KOH is investigated in detail. The concentration of NH 2 OH in TMAH/KOH is varied to optimize the etchant composition to obtain improved etching characteristics especially the etch rate and undercutting which are important parameters for increasing throughput. In this article, different methods explored to improve the etch rate of silicon have been discussed so that the researchers/scientists/engineers can get the details of these methods in a single reference.

Study on the photoelectrochemical etching process of semiconducting 6H–SiC wafer

Isotropic Etch for SiO2 Microcantilever Release with ICP System

Accelerated ICP Etching of 6H-Sic by Femtosecond Laser Modification

Demonstration of Irradiation-Resistant 4H-Sic Based Photoelectrochemical Water Splitting

Effect of Discharge Gas Composition on SiC Etching in an HFE-347mmy/O2/Ar Plasma

Oxidation Anisotropy of 4H-Sic Wafers During Chemical-Mechanical Polishing

Microscale pattern etch of 4H–SiC by inductively coupled plasma

Producing Silicon Carbide Micro and Nanostructures by Plasma‐Free Metal‐Assisted Chemical Etching

Selective Undercut of Undoped Optical Membranes for Spin-Active Color Centers in 4H-SiC

Image analysis development for optimization of 4H–SiC trench recovery treatment by combination of gas etching and sacrificial oxidation approaches

Electrochemical etching strategy for shaping monolithic 3D structures from 4H-SiC wafers

High-etch rate processes for performing deep, highly anisotropic etches in silicon carbide using inductively coupled plasma etching

Investigation on femtosecond laser combined with dynamic wet etching machining of SiC/SiC

Investigation and Modeling of Etching Through Silicon Carbide Vias (TSiCV) for SiC Interposer and Deep SiC Etching for Harsh Environment MEMS by DoE

Sub-damage-threshold plasma etching and profile tailoring of Si through laser-stimulated thermal desorption

Micro-trench free 4H-SiC etching with improved SiC/SiO2 selectivity using inductively coupled SF6/O2/Ar plasma

Optimization of Etching Processes for the Fabrication of Smooth Silicon Carbide Membranes for Applications in Quantum Technology

Combination of Plasma Electrolytic Processing and Mechanical Polishing for Single-Crystal 4H-SiC

Photoelectrochemical etching of ultra-wide bandgap β-Ga2O3 semiconductor in phosphoric acid and its optoelectronic device application

In-plasma photo-assisted etching of Si with chlorine aided by an external vacuum ultraviolet source

High speed silicon wet anisotropic etching for applications in bulk micromachining: a review