Abstract:In this study, the metallurgical mechanisms of inclusions during electron beam smelting (EBS) of a FGH4096 powder superalloy was investigated. The macroscopic morphology of the ingots, as well as the composition and structure of inclusions were studied. The effect of electron beam smelting parameters on the cooling rate, O/N content, number density and size of inclusions have been revealed. Besides, the mechanisms for inclusions removal and formation were elucidated. The results show that inclusions in the final solidification zone are mainly oxides (simple tetragonal CrO 2 , hexagonal Al 2 O 3 , and face-centered cube TiN), whereas the complex inclusions and carbon nitrides with Al 2 O 3 and TiN as the nucleation cores are mainly present in the matrix. With the increase in smelting power and time, both the cooling rate and O/N content decsrease, and the smelting power shows a greater impact on the cooling rate. The number density of total inclusions increases with the increase in the smelting power. As the smelting time increases, the number density of total inclusions decreases, while the size of complex inclusions and carbon nitrides increases. This is attributed to the combined effect of cooling rate and O/N concentration in the alloy under different smelting parameters. Thermodynamic calculations indicate that Al 2 O 3 forms in the solid-liquid phase region. The precipitation of TiN occurs when the alloy solidifies, and its precipitation temperature is higher than that of TiC. The lattice mismatch between Al 2 O 3 and TiN is 8.14%, while that between TiC and TiN is 6.94%, which effectively promotes the heterogeneous nucleation of complex inclusions and carbon nitrides. The formation mechanisms of complex inclusions and carbon nitrides provide a theoretical basis for purification of superalloys by electron beam metallurgy.

Formation and aggregation behavior of inclusions in Ni-based alloys with different Mg contents

The Formation Mechanism of Oxide Inclusions in a High-Aluminum Ni-Based Superalloy during the Vacuum Induction Remelting Process

Effects of aluminum and titanium additions on the formation of nonmetallic inclusions in nickel-based superalloys

In Situ Observation of Microstructure and Precipitate Phase Transformation during the Solidification of Mg‐Containing GH3625 Alloy at Different Cooling Rates

Study on the stability of different refractories during the melting process of a K4169 Ni-based superalloy

Effect of Mg Treatment on the Evolution of Inclusions in M50 Aerospace Bearing Steel Under Different S/O Ratio Conditions

Effect of Magnesium on Sulfide and Microstructure in Microalloyed Steel

Effect of Al Content on the Agglomeration Behavior of Inclusions in High Al Steel

A Kinetic Model for Oxide–Carbonitride Inclusion Heterogeneous Nucleation and Precipitation during Superalloy Solidification

Formation and Removal Mechanism of Nonmetallic Inclusions in 42CrMo4 Steel during the Steelmaking Process

Micro-alloying effects of Ni on the microstructure and mechanical properties of an Al-Zn-Mg-Cu-Sc-Zr alloy

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy

Effect of Ni addition on the mechanical and degradation properties of hollow glass microsphere/Mg alloy composites

Formation of intermetallic phases during solidification in Al-Mg-Mn 5xxx alloys with various Mg levels

Effect of nickel on the microstructure and mechanical property of die-cast Al–Mg–Si–Mn alloy

Agglomeration Behaviors of Different Types of Complex TiN Inclusions in High Titanium Wear Resistant Steel

Effect of Cooling Conditions on the Size and Morphology Evolution of MgAl2O4 Inclusions in Al‐Deoxidized Steel Coupling with Mg Treatment

Study on the metallurgical mechanisms of inclusions in the FGH4096 alloy during electron beam smelting

Effect of Interface Property on the Agglomeration Characteristic of Inclusions in High Al Steel with Different Al Contents

Effect of heat treatment on the microstructural evolution of a nickel-based superalloy additive-manufactured by laser powder bed fusion

Effect of Mg Addition on Inclusions in the Welding Heat-Affected Zone of Pressure Vessel Steels