Abstract:The presence of oxide-MnS complex inclusions is beneficial for the improvement of hydrogen resistance in pipeline steel. The effect of S and Mg contents on the generation mechanism of MnS, MgAl 2 O 4 , and MgO inclusions, and the heterogeneous nucleation principle of MnS on the surfaces of MgAl 2 O 4 and MgO were revealed using laboratory experiments, thermodynamic calculations, and density functional theory (DFT) computations. The inclusion characteristics in steel were evaluated by using a Scanning Electron Microscope in combination with an Energy Dispersive Spectrometer (SEM + EDS). It has been found that as the Mg content increased, MgAl 2 O 4 transformed into MgO, which can be well predicted by thermodynamic calculations. It was found that MnS exhibited the ability to nucleate heterogeneously on the surfaces of MgO and MgAl 2 O 4 inclusions. Furthermore, proper S content (approximately 30 ppm) can facilitate the formation of oxide-MnS complex inclusions, excess S content was not desired. The smaller the oxide inclusion, the easier to form wrapped MnS on the oxides. The nucleation ability of MnS and MgAl 2 O 4 was identified by DFT calculations and found that they followed the order of (111) MnS //(111) MgAl2O4 >(100) MnS //(100) MgAl2O4 >(110) MnS //(110) MgAl2O4 . Furthermore, the heterogeneous nucleation ability of MnS and MgO followed in the order of (111) MnS //(111) MgO > (100) MnS //(111) MgO > (100) MnS //(100) MgO . This study provides theoretical evidence supporting the heterogeneous nucleation ability of MnS on the surfaces of MgO and MgAl 2 O 4 . Moreover, it helps bridge the disparity between the calculation of MnS and MgO nucleation using the two-dimensional mismatch degree and the experimental findings.

Effect of Magnesium on Sulfide and Microstructure in Microalloyed Steel

Synergistic Effects of Mg Alloying and Subsequent Homogenization Treatment to Improve the Microstructure and Properties of Al-Mg-Mn Alloys

Effect of Mg Treatment on the Evolution of Inclusions in M50 Aerospace Bearing Steel Under Different S/O Ratio Conditions

Influence of the Mg Content on the Microstructure and Mechanical Properties of Al-xMg-2.0Si-0.6Mn Alloy

The Effect of Mn on the Microstructure of Spray-Deposited Al–20Si–5Fe–3Cu–1Mg Alloy

The effect of MnO2 additive on the microstructure and mechanical properties of magnesium aluminate spinel

Effect of Calcium Addition on Oxide and Sulfide Inclusions in Heavy Steel Ingot Simulated by Lab Experiments

Effect of Mg Addition on the Microstructure and Properties of a Heat-Affected Zone in Submerged Arc Welding of an Al-Killed Low Carbon Steel

The Effect of Magnesium Treatment on the Inclusions, Microstructure, and Mechanical Properties of M7 High-Speed Steel

The Effect of Alloying Elements on Formation and Evolution Mechanism of Manganese‐Containing Inclusions in Medium/High‐Manganese Steels

Revealing the Substantial Impact of Trace Mg Addition on the Microstructural Configuration of a Cast Al-Li-Cu-Zr Alloy under Various Conditions

In Situ Observation of Precipitation Behavior of MnS during Solidification of Steel Melt Intended for Production of Nonquenched and Tempered Steel

Effects of Si Content and Modification on Microstructure and Properties of In-situ Mg2Si/Mg Composites

Influences of Mg content on the microstructures and mechanical properties of cast Al–2Li–2Cu–0.2Zr alloy

Effect of Bismuth Content and Heating Rate on MnS Inclusions in Free-Cutting Steel

Effect of sulfur content on precipitation behaviour of MnS-containing inclusions in X70 pipeline steel

Effects of Mn Addition on the Microstructures and Mechanical Properties of the Mg-15Gd-1Zn Alloy

The Microstructure and Tensile Properties of a Newly Developed Mg–Al/Mg3Sb2 In Situ Composite in As-Cast and Extruded Conditions

Effect of trace Si on MgO·Al2O3 inclusion in ultra-low-carbon steel

Alloying effect of Mg on microstructure and mechanical properties at 300 °C of Al–5Cu–1Mn–0.5Ni heat-resistant alloy

Effect of magnesium on microstructure and properties of 440C stainless bearing steel melted under pressurized conditions