Abstract:The object of this study is to investigate the structure of cast magnesium alloy (Mg-Al-Zn) inoculated with nano particles of different allotropic forms of carbon. The aim of this study is to improve the processability and quality of critical load bearing magnesium alloy part castings. The tasks of the study are: attainment of efficient control of the alloy structural features by introduction of incremental additions of carbon nano particles; determination of the relationship between the quantity of the added inoculating carbon agent and α - solid solution grain size; determination of the influence of allotropic forms of carbon on the morphologic characteristics of the intergranular borders and the eutectoid (a+Mg17Al12); and comparative analysis of the phase composition of the standard ML5 alloy and the experimental alloy ML5 inoculated with carbon black, nanographite, and single-wall carbon nanotubes. The phase composition was determined by X-ray diffraction analysis using copper radiation. Micro X-ray spectral analysis was performed. The following findings were obtained. Using an optical microscope α – solid solution grain size was measured in the standard and inoculated alloy. In the samples of the alloy variants inoculated with 0.1 % wt. of carbon black, nanographite, and single-wall carbon nanotubes, the grain size was reduced by appox. 50 % compared with the standard alloy. In the samples of the alloy inoculated with 0.1 % wt. of nanographite and single wall carbon nanotubes, eutectoid (a+Mg17Al12) precipitates along the grain boundaries were thinner than those in the standard alloy samples and those inoculated with carbon black. X-ray diffraction analysis revealed no new phase formation. The X-ray diffraction patterns of the alloy samples with nanographite and nanotubes display weak peaks of free carbon, which may indicate the presence of free carbon in small quantities in the structure. The scientific and practical originality of the obtained results consists of the following: a technology of inoculation with incremental additions of allotropic forms of nano carbon, namely carbon black, nanographite, and single-wall carbon nanotubes, has been tested on a standard cast magnesium alloy (Mg-Al-Zn system) in an environment similar to the industrial production of critical magnesium cast components. It has been shown that the introduction of nanocarbon in a quantity of 0.1 % wt. can have a beneficial effect on the structural characteristics of ML5 cast magnesium alloy with no change in its phase composition. Nanographite and single wall carbon nanotubes with a regular structure contribute to the formation of thinner intergranular boundaries than amorphous carbon black.

Effect of Magnesium Modification on Inclusions and Carbide in As‐Cast 21‐4N Valve Steel

Effect of magnesium on microstructure and properties of 440C stainless bearing steel melted under pressurized conditions

Influence of magnesium treatment on inclusions and primary carbides in As-cast H13 die steel

Effect of Magnesium Treatment on Inclusion Formation and Solidification Structure Ferrite Stainless Steel 430

The Effect of Magnesium Treatment on the Inclusions, Microstructure, and Mechanical Properties of M7 High-Speed Steel

Effect of Trace Magnesium Addition on TiN Inclusions and Microstructure in 20CrMnTi Gear Steel

Influences of Partial Substitution of C by N on the Microstructure and Mechanical Properties of 9cr18mo Martensitic Stainless Steel

Effect of Mg Addition on Inclusions in the Welding Heat-Affected Zone of Pressure Vessel Steels

Effect of Magnesium on Sulfide and Microstructure in Microalloyed Steel

Effect of Mg Addition on the Microstructure and Properties of a Heat-Affected Zone in Submerged Arc Welding of an Al-Killed Low Carbon Steel

In Situ Observation of Microstructure and Precipitate Phase Transformation during the Solidification of Mg‐Containing GH3625 Alloy at Different Cooling Rates

Effect of Magnesium on the Austenite Grain Growth of the Heat-Affected Zone in Low-Carbon High-Strength Steels

Effect of Mg Treatment on the Evolution of Inclusions in M50 Aerospace Bearing Steel Under Different S/O Ratio Conditions

EFFECT OF MODIFICATION ON AS-CAST AND HEAT TREATED MICROSTRUCTURE OF SUPER-HIGH MANGANESE STEEL

Influence of carbon nanoparticle inoculation on the structure of ML5 casting magnesium alloy

Effect of Inclusion on Service Properties of GW103K Magnesium Alloy

Revealing the Substantial Impact of Trace Mg Addition on the Microstructural Configuration of a Cast Al-Li-Cu-Zr Alloy under Various Conditions

Effect of Increased N Content on Microstructure and Tensile Properties of Low-C V-microalloyed Steels

Optimization of Inclusion and Microstructure of As‐Cast Nonquenched and Tempered Steel F38MnVS with Trace Ce

Effect of Mg addition on TiN inclusions in GCr15 bearing steel

Effect of Mg treatment and cooling rate on primary carbides in GH3128 alloy