Abstract:In order to improve the cleanliness of steel, non-aluminum deoxidation processes have begun to replace aluminum deoxidation processes. Although the aluminum deoxidation process can reduce the oxygen content in steel to <10 × 10−6, this deoxidation method causes fatigue failure resulting from the formation of large-grained spherical (Ds-type) inclusions composed of calcium–aluminate. It also tends to lead to nozzle blockage during casting. Given the above problems, this study conducted an in-depth investigation of silicon–manganese deoxidation. Thermal experiments and thermodynamic calculations were used to assess the impact of different Mn–Si ratios on the oxygen content and inclusion characteristics during the deoxidation process of molten steel with different initial oxygen contents. The experimental samples were analyzed using an oxygen–nitrogen–hydrogen analyzer, a direct reading spectrometer, and an automatic scanning electron microscope. After that, the samples were electrolyzed to observe the 2D morphology and 3D morphology of the inclusions using scanning electron microscopy. Finally, thermodynamic calculations were carried out using FactSage to verify the experimental results. The results indicated that, regardless of the initial oxygen content, silicon–manganese deoxidation maintained the total oxygen content at 35 × 10−6. It effectively managed the plasticization of inclusions in molten steel, predominantly yielding spherical silicates while minimizing Al-containing inclusions. Nevertheless, as the initial content of [O] increased, the size and density of the silicate inclusions in the steel also increased. An optimal point in the number and size of inclusions was observed with an increased Mn–Si ratio. Moreover, the combined utilization of silicon–manganese deoxidation, diffusion deoxidation, and vacuum deoxidation enabled ultra-low oxygen content control of molten steel.

Effect of Mg Treatment on the Evolution of Inclusions in M50 Aerospace Bearing Steel Under Different S/O Ratio Conditions

Characteristics and Evolution of Inclusions in Ti‐Bearing Peritectic Steel with Mg Treatment

Effect of Magnesium on Sulfide and Microstructure in Microalloyed Steel

Effect of Calcium Addition on Oxide and Sulfide Inclusions in Heavy Steel Ingot Simulated by Lab Experiments

The Effect of Magnesium Treatment on the Inclusions, Microstructure, and Mechanical Properties of M7 High-Speed Steel

Effect of Mg Addition on Inclusions in the Welding Heat-Affected Zone of Pressure Vessel Steels

Influence of the MgO grade in MgO‐C refractory material and steel melt temperature on the inclusion population in Al‐treated steel

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Evolution Mechanism of Inclusions in H13 Steel with Rare Earth Magnesium Alloy Addition

Evolution of Inclusions and Associated Microstructure in Ti–Mg Oxide Metallurgy Steel

The Effect of Alloying Elements on Formation and Evolution Mechanism of Manganese‐Containing Inclusions in Medium/High‐Manganese Steels

Effect of MgO content in sinter on the softening–melting behavior of mixed burden made from chromium-bearing vanadium–titanium magnetite

Effect of Bismuth Content and Heating Rate on MnS Inclusions in Free-Cutting Steel

In Situ Observation of Microstructure and Precipitate Phase Transformation during the Solidification of Mg‐Containing GH3625 Alloy at Different Cooling Rates

Effect of Cooling Conditions on the Size and Morphology Evolution of MgAl2O4 Inclusions in Al‐Deoxidized Steel Coupling with Mg Treatment

Formation and Removal Mechanism of Nonmetallic Inclusions in 42CrMo4 Steel during the Steelmaking Process

Revolution and Control of Fe-Al-(Mg, Ti)-O Oxide Inclusions in IF Steel during 260t BOF-RH-CC Process

In Situ Observation of Precipitation Behavior of MnS during Solidification of Steel Melt Intended for Production of Nonquenched and Tempered Steel

Development of inclusions in 3104 alloy melt during heating and holding treatments

Effect of Mg Addition on the Microstructure and Properties of a Heat-Affected Zone in Submerged Arc Welding of an Al-Killed Low Carbon Steel

Effect of Silicon–Manganese Deoxidation on Oxygen Content and Inclusions in Molten Steel