Abstract:In order to improve the cleanliness of steel, non-aluminum deoxidation processes have begun to replace aluminum deoxidation processes. Although the aluminum deoxidation process can reduce the oxygen content in steel to <10 × 10−6, this deoxidation method causes fatigue failure resulting from the formation of large-grained spherical (Ds-type) inclusions composed of calcium–aluminate. It also tends to lead to nozzle blockage during casting. Given the above problems, this study conducted an in-depth investigation of silicon–manganese deoxidation. Thermal experiments and thermodynamic calculations were used to assess the impact of different Mn–Si ratios on the oxygen content and inclusion characteristics during the deoxidation process of molten steel with different initial oxygen contents. The experimental samples were analyzed using an oxygen–nitrogen–hydrogen analyzer, a direct reading spectrometer, and an automatic scanning electron microscope. After that, the samples were electrolyzed to observe the 2D morphology and 3D morphology of the inclusions using scanning electron microscopy. Finally, thermodynamic calculations were carried out using FactSage to verify the experimental results. The results indicated that, regardless of the initial oxygen content, silicon–manganese deoxidation maintained the total oxygen content at 35 × 10−6. It effectively managed the plasticization of inclusions in molten steel, predominantly yielding spherical silicates while minimizing Al-containing inclusions. Nevertheless, as the initial content of [O] increased, the size and density of the silicate inclusions in the steel also increased. An optimal point in the number and size of inclusions was observed with an increased Mn–Si ratio. Moreover, the combined utilization of silicon–manganese deoxidation, diffusion deoxidation, and vacuum deoxidation enabled ultra-low oxygen content control of molten steel.

Effect of Cooling Conditions on the Size and Morphology Evolution of MgAl2O4 Inclusions in Al‐Deoxidized Steel Coupling with Mg Treatment

Effect of Calcium Addition on Oxide and Sulfide Inclusions in Heavy Steel Ingot Simulated by Lab Experiments

Effect of Cooling Rate on the Grain Morphology and Element Segregation Behavior of Fe-Mn-Al-C Low-Density Steel During Solidification

Evolution of Al2O3 Inclusions by Magnesium Treatment in H13 Hot Work Die Steel

Effect of trace Si on MgO·Al2O3 inclusion in ultra-low-carbon steel

Effect of Deoxidizing and Alloying Routes on the Evolution of Non-Metallic Inclusions in 55SiCr Spring Steel

Effect of Cooling Rate on Oxide Inclusions During Solidification of 304 Stainless Steel

Effect of Mg Treatment on the Evolution of Inclusions in M50 Aerospace Bearing Steel Under Different S/O Ratio Conditions

Evolution of MnO–SiO2–Al2O3–MgO inclusions during heat treatment at 1100 °C

Transient Behavior and Thermodynamics of Inclusions in Al-Ti-Deoxidized and Ca-Treated Steel

Microstructural Evolution of Undercooled Fe83Ga17 Magnetostrictive Alloys

Effects of Calcium Addition on Nonmetallic Inclusions in High‐Al Steel

Effect of Magnesium on Sulfide and Microstructure in Microalloyed Steel

Effect of Magnesium Treatment on Inclusion Formation and Solidification Structure Ferrite Stainless Steel 430

Effect of Silicon–Manganese Deoxidation on Oxygen Content and Inclusions in Molten Steel

Formation and Removal Mechanism of Nonmetallic Inclusions in 42CrMo4 Steel during the Steelmaking Process

Influence of the MgO grade in MgO‐C refractory material and steel melt temperature on the inclusion population in Al‐treated steel

The Effect of Mn on the Microstructure of Spray-Deposited Al–20Si–5Fe–3Cu–1Mg Alloy

Evolution of Inclusions and Associated Microstructure in Ti–Mg Oxide Metallurgy Steel

Effect of Al Content on the Agglomeration Behavior of Inclusions in High Al Steel

In Situ Observation of Microstructure and Precipitate Phase Transformation during the Solidification of Mg‐Containing GH3625 Alloy at Different Cooling Rates