Abstract:China Spallation Neutron Source(CSNS) beam power will upgrade to 500 kW(CSNS-II), energy gain of H- linac will up to 300 MeV from 80 MeV, and the 648 MHz βg=0.6 5-cell superconducting elliptical cavity will be adopted to accelerate the H- from 150 to 300 MeV. Accompanied with the advantage of high accelerating gradient, simple structure, easy post-processing, weak stiffeness and detuning is the shortcoming of elliptical cavity, this study analysis detuning characteristic of the elliptical cavity. With code COMSOL Multiphysics, helium pressure sensitivity coefficient KP and lorentz force detuning factor KL of bare cavity was calculated under two end fixed conditions, KP=–45.705 Hz/mbar(1 mbar=100 Pa) and KL=1.574 Hz/(MV/m)2. Stiffener ring was designed and optimized to reduce the Helium pressure sensitivity coefficient and lorentz force detuning factor, and double ring was chosen to improve the detuning of elliptical cavity at last by vast calculation and analysis, the position of stiffener ring was optimized at 75 and 120 mm under two end fixed boundary, Helium pressure sensitivity coefficient drop down to KP=6 Hz/mbar, lorentz force detuning factor drop down to KL=0.43 Hz/(MV/m)2. Moreover, elastic boundary was used to analyze helium pressure sensitivity coefficient and lorentz force detuning factor, more realistic results were got under tuner end 30 kN/mm boundary and the other end fixed condition, KP=4.8 Hz/mbar and KL=1.99 Hz/(MV/m)2, meet engineering requirements. In addition, dynamic lorentz force detuning was analyzed qualitatively with code CST. And natural frequency of cavity was calculated by code Workbench, results show that nature frequency is far from RF pulse repetition rate and ambient vibration frequency, no resonance happen.

MECHANICAL ANALYSIS AND DESIGN OF THE PEFP LOW BETA CAVITY

DESIGN OF THE PEFP LOW BETA CRYOMODULE

Mechanical design and analysis for a low beta squeezed half-wave resonator

Control and Measurement System for the Tuning of A Pefp Low-Beta Superconducting Rf Cavity

Mechanical Analysis of Lowβ162.5 MHz Taper HWR Cavity

Design Of A Beta=0.45, F=350 Mhz Spoke Cavity

Frequency and Length Adjustment of A PEFP Low-Beta Dumbbell

A Study of Dynamic Lorentz Force Detuning of 650 MHz βg= 0.9 Superconducting Radiofrequency Cavity

Study On High Order Modes Of A Beta=0.45, F=350mhz Spoke Cavity

Rf superconductivity activities of pefp*

Design of a ββ = 0.45, f = 350 MHz Spoke Cavity

Multipacting Behavior Research in a PEFP Low-Beta Superconducting RF Cavity and in a PEFP Fundamental Power Coupler

Status of the pefp superconducting rf project *

Development of a Prototype Niobium SRF Cavity for the PEFP Proton Superconducting Linac

Design and Testing of an Ultralow Q CBPM

Rf Optimization and Analysis of the 805-Mhz Cavity for the Mucool Program Using Ace3p

Design of a 325MHz Beta=0.12 superconducting single spoke cavity for China-ADS

Detuning Analysis of the Superconducting Elliptical Cavity for CSNS-Ⅱ Linac

Design study on very low Beta spoke cavity for China-ADS

Design, fabrication and test of a taper-type half-wave superconducting cavity with the optimal beta of 0.15 at IMP

Electromagnetic Design and Beam Dynamics Simulation of a New Superconducting Accelerating Structure for Extremely Low Β Protons