Abstract:A TD-split basal texture with two peaks highly tilted from the normal direction (ND) towards the transverse direction (TD) is usually developed in Mg-Zn-Ca plates and can effectively improve ductility and formability. In the present study, the texture evolution during cold rolling and subsequent annealing of a Mg-2Zn-1Ca plate with initial TD-split texture was investigated, and new insights into the mechanisms of texture evolution were obtained. The results show that a dumbbell-shaped basal texture transformed into an elliptical shape after 41% cold rolling. The random distribution of prismatic planes became preferred with largely parallel to the rolling direction (RD). Crystal plasticity simulations revealed that basal slip was the predominant deformation mode, and inclined basal poles toward the ND. The activation of other non-basal slips would retard this tendency. Prismatic slip with a relative activity of 20% to 30% preserved the pre-existing TD-split texture after a high rolling reduction of 41%. Pyramidal slip prevented the formation of basal fiber and lead to a spreading of basal poles toward the RD mainly at strains over 29%. After full recrystallization, the elliptical TD-split basal texture became a dumbbell-shaped TD-split texture. Grain nucleation was observed at grain boundaries (GBN mechanism), within deformation twins (DTN mechanism), and near precipitates (PSN mechanism). GBN and DTN mainly developed a TD-split basal-texture. Instead of the formation of random orientations as considered previously, PSN produced a TD-split basal-texture, and the basal poles exhibited a much wider distribution with high angle of the peaks off the ND. The grains nucleated by GBN, DTN, and PSN did not exhibit preferred growth, and consequently, the texture hardly changed during subsequent grain growth.

Unexpectedly Formed Strong Basal Texture in a Rolled Mg-Zn-Ca-Mn Alloy Sheet

Formation of Unusual Rolling Texture in a Mg-Al-Mn Alloy Sheet by Large-Strain Hot-Rolling

Twinning-mediated Texture Weakening in a Basal-Textured Mg-6Al-1Zn (mass%) Alloy Sheet by a Novel Cold-Sample Rolling Method

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Understanding the mechanisms of texture evolution in an Mg-2Zn-1Ca alloy during cold rolling and annealing

Texture and Texture Randomization of Rolling Mg Alloy Sheet

Microstructure evolution and mechanical property of Mg-3Al alloys with addition of Ca and Gd during rolling and annealing process

Texture Evolution of AZ31 Magnesium Alloy Sheets During Warm Rolling

Non-Basal Slip Induced Rare Earth Texture Evolution in Mg-14Gd-0.5Zr (wt.%) Alloy During the Traditional Hot Rolling

Rolling Temperature and Subsequent Annealing on Microstructure, Texture and Mechanical Properties of Consecutive Rolled Mg-2.0zn-0.8gd Alloy

Texture weakening and ductility improvement of Mg-1.1Mn-0.5Al alloy via medium temperature-high reduction rolling: twinning variants selection and dynamic recrystallization mechanism

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

Activation of {1 01¯2} Twinning and Slip in High Ductile Mg–2.0Zn–0.8Gd Rolled Sheet with Non-Basal Texture During Tensile Deformation at Room Temperature

Coupling Thermomechanical Processing and Alloy Design to Improve Textures in Mg-Zn-Ca Sheet Alloys

Oriented Nucleation Causing Unusual Texture Transition During Static Recrystallization Annealing in Cold-Rolled Mg–Zn–Gd Alloys

Effect of Calcium Addition on Microstructure and Texture Modification of Mg Rolled Sheets

Texture weakening effect from { 10 1 ̅ 1 } twins induced static recrystallization in ambient extrusion AZ31 magnesium alloy

Strength-ductility balance of Mg-1.03Ca-0.47Mn Mg alloy sheet produced by rolling and annealing

Microstructure and Texture Evolution of the Magnesium Alloy ZMX210 during Rolling and Annealing

The effect of grain size on texture evolution and mechanical properties of an AZ31 magnesium alloy during cold-rolling process

Understanding the weakening of texture in multiaxial forged ultrafine-grained strong and ductile Mg-2Zn-2Gd alloy