Abstract:The coarse segregative eutectic phases, emerged in the twin roll casting (TRC) process of Mg strips, which cannot be resolved solely by controlling the processing variables or post heat treatment, are detrimental to the subsequent rolling deformation. Considering it, we introduce the pre-rolling steps on the TRC Mg-4Al-2Sn-1 Zn (ATZ421) alloys, which is expected to facilitate the dissolution of these segregative phases by increasing distortion of crystal lattices and rolling stress, and further investigate the effect of a single pass or two passes pre-rolling on the microstructure evolution and tensile properties. It indicates that the pre-rolled alloy with two passes presents more uniform precipitates and higher twinning density in comparison with that using a single pass. The uniform distribution of precipitates in two passes pre-rolling is due to the increase in density of dislocations and deformed twins, which results in more distortion of crystal lattices with more stored energy, facilitating the diffusion of solutes. Moreover, the pre-rolling of two passes introduces more rolling stress into Mg matrix, which is beneficial for the crush of coarse eutectic phases, and further accelerates the sufficient dissolution of second phases. After the subsequent rolling and annealing processes, the sheet with pre-rolling deformation of two passes shows finer microstructure, which mainly benefits from the pinning effects of uniform nano-sized precipitates. As a result, the annealed sheet with two-pass pre-rolling deformation exhibits an advantageous combination of high strength and high ductility with fine microstructure, showing an ultimate tensile strength of similar to 297 MPa, a yield strength of similar to 205 MPa and an elongation of 25.0%. This work provides an effective method of dissolving the coarse segregative phases in the TRC Mg alloys with significant potential for industrial production.

Rolling Temperature and Subsequent Annealing on Microstructure, Texture and Mechanical Properties of Consecutive Rolled Mg-2.0zn-0.8gd Alloy

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Effects of Gd Concentration on Microstructure, Texture and Tensile Properties of Mg–Zn–Gd Alloys Subjected to Large Strain Hot Rolling

Microstructure and Texture Evolution of Hot-Rolled Mg-3Gd Alloy During Recrystallization

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Effect of rolling temperature on microstructure and mechanical properties of Mg-Gd-Y-Zr alloy

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Microstructure and Mechanical Properties of Rolled Mg-12gd-3y-0.4zr Alloy Sheets

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Effects of Hot Rolling Processing on Microstructures and Mechanical Properties of Mg–3%Al–1%Zn Alloy Sheet

Microstructure and Tensile Properties of Rolled Mg-4Al-2Sn-1Zn Alloy with Pre-Rolling Deformation

Effect of cold rolling on the microstructure and mechanical properties of MG-8GD-3Y-0.5ZR alloy

Influence of Finish Rolling Temperature on the Microstructure and Mechanical Properties of Mg-8.5Al-0.5Zn-0.2Mn-0.15Ag Alloy Sheets

The Edge Crack, Texture Evolution, and Mechanical Properties of Mg-1Al-1Sn-Mn Alloy Sheets Prepared Using On-Line Heating Rolling

Microstructure and Mechanical Anisotropy of the Hot Rolled Mg-8.1al-0.7zn-0.15ag Alloy

Microstructure and Mechanical Properties of Mg-Gd-Y-Zn-Mn Alloy Sheets Processed by Large-Strain High-Efficiency Rolling

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

Effect of annealing temperature on microstructure and mechanical properties of rolled Mg-1Li-3Al-1Zn-0. 3( Al5Ti1B) alloy

Influences of Tensile Temperature on the Mechanical Properties of Rolled Mg-Zn-Gd Sheets with Non-Basal Texture

Twins, shear bands and recrystallization of a Mg–2.0%Zn–0.8%Gd alloy during rolling