Abstract:Asymmetric hot rolling was used to fabricate the high-strength Mg-9Gd-4Y–1Zn-0.8Mn (wt.%) alloys, which is strengthened by the lamellar long-period stacking ordered (LPSO) phases inside grains and the block-shaped LPSO phases surrounding grain boundaries. The reduction in total thickness shows a significant impact on the microstructure, texture, and mechanical properties of the alloy sheets. By keeping the velocity ratio between the top and lower rollers at 1.3, the shear strain is introduced all across the sheet thickness. The as-rolled sample exhibits a bimodal-grained structure made up of fine recrystallized (DRXed) grains with relatively random orientation and coarse elongated non-recrystallized (unDRXed) grains with intense basal texture and profuse substructure. As rolling strain increases, the volume fraction of the DRXed region and the basal texture intensity of the unDRXed region gradually increase. The dominating prismatic slip as well as the moderate basal slip and pyramidal slip are activated during rolling. The triggering of prismatic slip, among the activated multiple slip systems, results in the development of [101¯0]//RD texture component at high strains. The alloy sheet that underwent severer rolling strain (56.3%R sample) shows higher ultimate tensile strength (411 MPa) and tensile yield strength (348 MPa) but lower elongation to failure (3.5%). The dominant strengthening mechanisms for the preferable mechanical properties should be grain boundary strengthening of fine DRXed grains, texture strengthening of coarse elongated unDRXed grains, short-fiber strengthening of block-shaped LPSO phases, and dispersion strengthening of profuse lamellar LPSO phases and dense tiny Mg5(Gd, Y) particles.

Microstructure and Mechanical Anisotropy of the Hot Rolled Mg-8.1al-0.7zn-0.15ag Alloy

Microstructure Evolution and Mechanical Properties of High-Strength Mg-Gd-Y-Zn-Mn Alloy Processed by Asymmetric Hot Rolling

Influence of Finish Rolling Temperature on the Microstructure and Mechanical Properties of Mg-8.5Al-0.5Zn-0.2Mn-0.15Ag Alloy Sheets

Microstructure and Mechanical Properties of Rolled Mg-12gd-3y-0.4zr Alloy Sheets

Study on Microstructure and Mechanical Properties of Hot Rolled Mg97Zn1Y2 Alloy Sheet

Microstructure and mechanical property of multi-pass low-strain rolled Mg-Al-Zn-Mn alloy sheet

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Microstructure and Mechanical Properties of Hot-Rolled Mg-Zn-Y-Zr Magnesium Alloy

Dynamic Precipitation, Microstructure and Mechanical Properties of Mg-5Zn-1Mn Alloy Sheets Prepared by High Strain-Rate Rolling

Microstructure and Mechanical Properties of Mg 97Y 2ZN 1 Alloy Sheets Processed by Hot Rolling

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

A Comparison of Microstructure and Mechanical Properties of Mg–9Al–1Zn Sheets Rolled from As-Cast, Cast-Rolling and As-Extruded Alloys

Microstructure and Mechanical Properties of Rolled Sheets of Mg–Gd–Y–Zn–Zr Alloy: As-cast Versus As-Homogenized

Microstructure Evolution and Tensile Properties of Hot Rolled Mg–6Al–3Sn Alloy Sheet at Elevated Temperatures

Microstructures evolution, texture characteristics and mechanical properties of Mg-2.5Nd-0.5Zn-0.5Zr alloy during the high strain rate hot-rolling

Rolling Temperature and Subsequent Annealing on Microstructure, Texture and Mechanical Properties of Consecutive Rolled Mg-2.0zn-0.8gd Alloy

Microstructure and Tensile Properties of Mg-3Al-1Zn Sheets Produced by Hot-Roller-cold-material Rolling

Effect of Hot-Rolling on Microstructures and Mechanical Properties of Extruded Mg-6gd-3.2y-Xzn-0.5zr Sheet

Microstructure and Mechanical Properties of Mg-Gd-Y-Zn-Mn Alloy Sheets Processed by Large-Strain High-Efficiency Rolling

Microstructure and Mechanical Properties of Mg–6Al–1Sn–0.3Mn Alloy Sheet Fabricated Through Extrusion Combined with Rolling

High performance Mg-8Gd-4Y-1Zn-0.5Al alloy with long-period stacking ordered structure by hot rolling