Abstract:In our previous work, we designed a new as-cast Mg–Y–Zn–Al–Li alloy with a high elastic modulus of 52.9 GPa. The alloy was further subjected to hot deformation under different rolling reductions (40% and 80%) in this work. The microstructure evolution, texture and mechanical properties of Mg–Y–Zn–Al–Li alloy compared with Mg–Y–Zn alloy were systematically investigated. The result showed that the Mg–Y–Zn–Al–Li alloy with a rolling reduction of 40% displayed a more homogeneous fine microstructure and a weakened basal texture, accompanied by the formation of Al–Li and nano-precipitates Al0.9Li34.3Mg64.5Zn0.3 phase. Compared with the Mg–Y–Zn alloy, the strength and ductility of the alloy also were obviously enhanced while possessing a weak mechanical anisotropy. Grain refinement and second phase strengthening (fine Al–Li phase and nano-precipitates Al0.9Li34.3Mg64.5Zn0.3) mainly contributed to the enhanced strength. The texture weakening, low dislocation density and non-basal slip commonly guaranteed the high ductility, especially the weakened texture gave rise to the low anisotropy. When the rolling reduction increased to 80%, the volume fraction of recrystallized grains in Mg–Y–Zn–Al–Li alloy increased significantly to73.3%. As a result, the symmetry of the texture distribution around the ND was appreciably improved. In addition, the lower dislocation density and more non-basal slip in the Mg–Y–Zn–Al–Li alloy with the rolling reduction of 80% further enhanced the ductility. Simultaneously, the anisotropic degree of mechanical was effectively minimized, which was mainly attributed to the weak symmetric texture caused by fine DRXed grains with random misorientation and non-basal pyramidal <c+a> slip.

Strength-ductility balance of Mg-1.03Ca-0.47Mn Mg alloy sheet produced by rolling and annealing

High strength-ductility synergy and low anisotropy of Mg-4.5Al-2.6Zn-0.3Mn alloy sheet achieved by annealing after rolling

Effect of annealing treatment on the microstructure and mechanical properties of warm-rolled Mg–Zn–Gd–Ca–Mn alloys

Insights into the evolution of texture and mechanical properties during warm rolling and annealing of Mg–2Zn-0.5Ca alloy

Effect of Warm Rolling on the Microstructure, Texture and Mechanical Properties of Extruded Mg–Zn–Ca–Ce/La Alloy

Development of low-alloyed Mg–Zn–Ca–Sn–Mn alloy with high strength-ductility synergy by sub-rapid solidification and hot rolling

Strength-ductility synergy in Mg98.3Y1.3Ni0.4 alloy processed by high temperature homogenization and rolling

Microstructure evolution and mechanical property of Mg-3Al alloys with addition of Ca and Gd during rolling and annealing process

Microstructure, texture and mechanical properties of the rolled high modulus Mg-Y-Zn-Al-Li alloy

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Achieving exceptional ultrahigh-strength in low-alloy Mg-1Al-1Ca-0.4Mn (wt%) alloy by regulating bimodal microstructure

Microstructure and mechanical property of multi-pass low-strain rolled Mg-Al-Zn-Mn alloy sheet

Effect of Dual Deformation Processes on the Microstructure and Mechanical Properties of Low-Alloyed Mg-Zn-Ca-Mn Alloy

An investigation on annealing process and strengthening mechanism of cold rolled Mg-10Li-3Al-2.8Zn alloy

Ameliorating the edge cracking behavior of Mg-Mn-Al alloy sheets prepared by multi-pass online heating rolling

Non-basal Slips Mediated Dynamic Recrystallization Promote Synergistic Strengthening and Toughening of Centrifugal Casting Mg–1.1Mn–0.5Al Alloy via High Strain Rolling

Deformation mechanism, orientation evolution and mechanical properties of annealed cross-rolled Mg-Zn-Zr-Y-Gd sheet during tension

Microstructure, Texture Evolution, and Mechanical Properties of Thin AZ31B Mg Alloy Sheets Prepared by Two-Stage Rolling

High performance Mg-8Gd-4Y-1Zn-0.5Al alloy with long-period stacking ordered structure by hot rolling

A Rolled Mg‐8Al‐1Sm‐1Zn Alloy with High Strength‐Ductility via Single‐Pass Liner Rolling

Evolution of the Microstructure and Mechanical Properties of AZ31 Magnesium Alloy Sheets during Multi-Pass Lowered-Temperature Rolling