Abstract:High-strength, high-porosity and relatively low-shrinkage ZrO 2 ceramics were successfully fabricated by material extrusion 3D printing technology via optimizing CaCO 3 addition and sintering temperature. The effects of different CaCO 3 additions on the performance, phase formation, and microstructure of porous ZrO 2 ceramics sintered at different temperatures were systematically investigated and discussed. The results showed that flexural strength, porosity and shrinkage of the ZrO 2 ceramics were significantly affected by CaCO 3 addition and sintering temperature. The appropriate addition of CaCO 3 could promote sintering and phase transformation of m-ZrO 2 , increase the number and size of pores in the matrix. The corresponding flexural strength and porosity of the sintered samples increased, while the shrinkage rate decreased. The raised sintering temperature appropriately facilitated the formation of CaZrO 3 . Microstructural analysis indicated that CaZrO 3 exhibited a larger polyhedral bulk morphology, mainly distributed at the edges of pores, which could stabilize the pore structure and thicken the sintering necks, and thereby exhibiting well-balanced comprehensive performance. The ZrO 2 ceramics with high flexural strength, high porosity and relatively low shrinkage rate were achieved by adding 15 wt% CaCO 3 and sintering at 1450 °C. The resulting flexural strength and porosity were 27.33 MPa and 67.62 %, respectively, presenting an improvement of 563.35 % and 13.69 % compared to ZrO 2 ceramics without CaCO 3 . Moreover, the shrinkage rates in the X-direction (9.98 %), Y-direction (9.62 %), and Z-direction (9.94 %) significantly reduced, decreasing by 38.28 %, 38.10 %, and 41.46 %, respectively.

Dense and Strong Calcite Ceramics Prepared by Room‐temperature Cold Sintering Based on High‐pressure‐enhanced Solubility

Dense gypsum ceramics prepared by room-temperature cold sintering with greatly improved mechanical properties

Improved Mechanical Properties of 3YSZ Ceramics Prepared by Pressure-less Sintering Assisted by Cold Sintering under Mild Conditions

Highly Dense 0.3cacenbwo8‐0.7lamno3 Composite Ceramics Fabricated by Cold Sintering Process

Densification mechanism, microstructure and mechanical properties of ZrC ceramics prepared by high-pressure spark plasma sintering

Zeolite ceramics with ordered microporous structure and high crystallinity prepared by cold sintering process

Microstructures and Mechanical Properties of Pressureless Sintered Ca-3(PO4)(2)/Si3N4 Composite Ceramics

Preparation and Microwave Dielectric Properties of Calcite (caco3) Ceramics

Achieving high-strength, high-porosity and relatively low-shrinkage in extrusion-based 3D printed ZrO 2 ceramics by adjusting CaCO 3 addition and sintering temperature

Highly dense 0.3CaCeNbWO 8 ‐0.7LaMnO 3 composite ceramics fabricated by cold sintering process

Densification, Microstructure and Mechanical Properties of Multicomponent (tizrhfnbtamo)c Ceramic Prepared by Pressureless Sintering

Fabrication, Structure and Properties of Porous SiC Ceramics with High Porosity and High Strength

Low-temperature preparation of porous SiC ceramics using phosphoric acid as a pore-forming agent and a binder

Cold Sintering Process for ZrO2‐based Ceramics: Significantly Enhanced Densification Evolution in Yttria‐doped ZrO2

Lightweight Calcium-Silicate-Hydrate Nacre with High Strength and High Toughness

Low-temperature Densification and Mechanical Properties of Monolithic Mullite Ceramic

Effect of molding pressure on fabrication of low-crystalline calcite block

Preparation of Dense Β-Casio3 Ceramic with High Mechanical Strength and HAp Formation Ability in Simulated Body Fluid

Thermal insulating performance and compressive strength of ZSM-5 zeolite ceramics by cold sintering process

Nearly dense cordierite bonded silicon carbide ceramics prepared by hot pressing sintering at 1650°C

A simple method for the preparation of cordierite ceramics with high strength and low thermal expansion coefficient