Abstract:SiC/SiC composites have a promising application prospect in the fields of aero-engine turbine blades and other hot-end components due to their excellent properties. It is difficult to machine SiC/SiC composites by traditional mechanical processing because of the ultra-high hardness and anisotropic character. The routinely laser direct processing in the air produce thermal effect damage, resulting in heat-affected zones and microcracks. Here high-temperature chemical-assisted nanosecond laser processing was investigated to realize one-step in-situ fast etching without causing damage to the structure of SiC/SiC composites. Firstly, the chemical wet etching only occurred in the laser-induced local high-temperature region. There was no additional etching damage to the substrate material in the region where the temperature was relatively low. Secondly, chemical liquid served as a transparent constraint layer, the ablation pressure on the material increased in a liquid confined environment. In comparison with laser direct etching in the air, the exposed fiber was not a needle-like structure and tubular structure but turned into a thin and flat tongue-like structure. The etching behavior of 0° fiber layer, 90° fiber layer, and crossing regions of fibers of different directions at low and high laser intensities were studied. Further, the hardness and friction coefficient of SiC/SiC composites after laser direct etching in the air and high-temperature chemical-assisted laser etching were compared. The chemical elementary composition before and after etching was measured to reveal the oxidized and carbonized characteristics. It was concluded that the action mechanism was the combined result of high-temperature decomposition, laser-induced ablation pressure in the liquid confined region, and local chemical wet etching. The results demonstrate that high-temperature chemical-assisted laser etching has some advantages over traditional laser beam machining and is a potential processing method for SiC/SiC composites.

Process mechanism of ultrafast laser multi-focal-scribing for ultrafine and efficient stealth dicing of SiC wafers

Stealth Dicing of SiC Using Femtosecond Laser Bessel Beam

Ultrafast pulsed laser stealth dicing of 4H-SiC wafer: Structure evolution and defect generation

Precision Layered Stealth Dicing of SiC Wafers by Ultrafast Lasers

Investigation on the Processing Quality of Nanosecond Laser Stealth Dicing for 4H-SiC Wafer

Multi-focal Picosecond laser vertical slicing of 6 inch 4H-SiC ingot

Modulation of Ultrafast Laser-Induced Modified Structure Inside Silicon Carbide for Thin Wafer Dicing

Dual Laser Beam Asynchronous Dicing of 4H-SiC Wafer

Slicing of 4H‐SiC Wafers Combining Ultrafast Laser Irradiation and Bandgap‐Selective Photo‐Electrochemical Exfoliation

Laser slicing of 4H-SiC wafers based on picosecond laser-induced micro-explosion via multiphoton processes

High-Speed Dicing of SiC Wafers with 0.048 mm Diamond Blades via Rolling-Slitting

Super stealth dicing of transparent solids with nanometric precision

Influence of Surface Preprocessing on 4H-SiC Wafer Slicing by Using Ultrafast Laser

One-step in-situ low damage etching of SiC/SiC composites by high-temperature chemical-assisted laser processing

Surface Micromorphology and Nanostructures Evolution in Hybrid Laser Processes of Slicing and Polishing Single Crystal 4H-Sic

Internal modified structure of silicon carbide prepared by ultrafast laser for wafer slicing

A State-of-the-Art Review of Fracture Toughness of Silicon Carbide: Implications for High-Precision Laser Dicing Techniques

Materials removal mechanism of single crystalline SiC with laser-induced periodic surface structures (LIPSS)

Cohesive behavior of single crystalline silicon carbide scribing by nanosecond laser

4H-SiC wafer slicing by using femtosecond laser double-pulses

Femtosecond Laser Modification of Silicon Carbide to Improve the Materials Removal Efficiency