Abstract:The root mean square (rms) surface roughness extracted from atomic force microscopy is widely employed to complement the characterisation of ion implantation processes in 4H-SiC. It is known that the protection of a carbon film eliminates or mitigates roughening of the SiC surface during postimplantation annealing. This study, based on a rich original data collection of Al+ ion implanted 4H-SiC samples, allows for a quantitative description of the surface morphology as a function of the annealing temperature and time and of the Al implanted concentration. With increasing thermal budget, the evolution from flat, to blurred with ripples, granular, and finally jagged surface, results in a monotonous increase in the root mean square roughness. Additional information is given by the trends of the roughness exponent and of the correlation length, extracted from the height-height correlation function, which account for the surface evolution below 1700°C and for the effect of the Al implanted concentration on the ripple size, respectively. A combination of low roughness parameter and high correlation length identify the transition from ripples to jagged morphology. LAY DESCRIPTION: Selective area doping is a key step in the fabrication of hexagonal Silicon Carbide (4H-SiC) power electronic devices. It is achieved by ion implantation followed by a high temperature postimplantation annealing to restore the lattice and electrically activate the dopants. Aluminium, the preferred p-type dopant, is electrically activated at temperature ranging between 1500°C and 2000°C. The time required to complete the activation process is longer the lower the annealing temperature, spanning between some minutes and hundreds of hours. During annealing, 4H-SiC wafers are encapsulated by a temperature-resistant carbon layer (C-cap) in order to avoid step bunching and reduce surface roughening. Nevertheless, surface modifications can occur at high temperature. For this reason, the characterisations of 4H-SiC doping processes report not only the electrical activation of the dopants, but also the root mean square surface roughness obtained at the end of the process. However, rms values can be scattered because technological parameters such as the heating system and the way to deposit and remove the C-cap can affect the final result as well as the process parameters. Furthermore, the C-cap resistance to long annealing has been proven only by electrical measurements, but the surface morphology has never been observed. This work presents a quantitative characterisation of the surface morphology of Al implanted 4H-SiC as a function of the annealing temperature, time and of the Al implanted concentration, independent of the heating system and of the C-cap technology. The produced sample collection allowed to correlate characteristic surface features with the corresponding quantities extracted from image analysis that can be more sensitive to process parameters than the sole rms. These findings can be used to enrich process optimisation tools.

Investigation of GaAs wafer surface blistering by hydrogen implantation

Investigation of GaAs Wafer Surface Blistering by Hydrogen Implantation

Study of Surface Morphology in GaAs by Hydrogen and Helium Implantation at Elevated Temperature

Lattice Defects and Exfoliation Efficiency of 6H-SiC via H2+ Implantation at Elevated Temperature

Thermodynamics of Ion-Cutting of β-Ga 2 O 3 and Wafer-Scale Heterogeneous Integration of a β-Ga 2 O 3 Thin Film onto a Highly Thermal Conductive SiC Substrate

High-Pressure Water-Vapor Annealing for Enhancement of A-Si:H Film Passivation of Silicon Surface

Molecular Dynamics Study on Splitting of Hydrogen-Implanted Silicon in Smart-Cut® Technology

The Study on Defects of Germanium-on-Insulator Fabricated by a Low Temperature Smart-Cut Process

Direct Detection of Free H2 Outgassing in Blisters Formed in Al2O3 Atomic Layers Deposited on Si and Methods of Its Prevention

Effect of Thermal Pretreatment on Electron-Irradiation Induced Defects in Hydrogen-Grown Silicon

Blister formation in He-H co-implanted InP: A comprehensive atomistic study

Low-temperature Annealing of Polycrystalline Si/sub 1-X/ge/sub X/ after Dopant Implantation

Irradiation hardening induced by blistering in tungsten due to low-energy high flux hydrogen plasma exposure

Effect of surface orientation on blistering of copper under high fluence keV hydrogen ion irradiation

Surface blistering and void swelling of α-Al2O3 irradiated with H2+ ions followed by 1000, 1200 °C annealing

Exploring crystal recovery and dopant activation in coated laser annealing on ion implanted 4H–SiC epitaxial layers

High temperature annealing of hydrogenated amorphous silicon carbide thin films

Effect of Hydrogen Annealing on Voids in arge-Diameter Czochralski Silicon

Effect of crystal orientation on low flux helium and hydrogen ion irradiation in polycrystalline tungsten

Creating nanostructures on silicon using ion blistering and electron beam lithography

4H-SiC surface morphology after Al ion implantation and annealing with C-cap