Abstract:Electroplated copper thin films have started to be applied to not only interconnections in printed wiring boards, but also thin film interconnections and TSV (Through Silicon Via) in semiconductor devices because of its low electric resistivity and high thermal conductivity. Thus, the electrical reliability of the electroplated copper interconnections was investigated experimentally. Self-made electroplated copper thin film interconnections were used for the evaluation. Electroplating conditions are as follows. The thin film interconnections were made by damascene process for electromigration tests. The applied current density during the test was varied from 1 MA/cm2 to 10 MA/cm2. Abrupt fracture caused by the local fusion was often observed in the as-electroplated interconnections within a few hours during the test. Since there were a lot of porous grain boundaries in the as-electroplated thin films, the local high Joule heating should have caused the fusion at one of the porous grain boundaries. Actually, it was confirmed that the failure rate increased linearly with the square of the amplitude of the applied current density. However, the diffusion of copper atoms caused by electromigration was enhanced significantly when the film was annealed at 400°C. Many voids and hillocks were observed on their surfaces. This change of the fracture mode clearly indicates the improvement of the crystallographic quality of the annealed film. It was also observed that the stress-induced migration was activated substantially in the annealed film. Large voids and hillocks grew during the custody of the film even at room temperature without any application of current. This stress-induced migration was caused by the increase of residual tensile stress of about 200 MPa in the annealed film. It was also found that sulfur atoms segregated in the grown hillocks, though no sulfur atoms were found by EDX in the initial as-electroplated interconnections or other area in the annealed thin film interconnections. Thus, the hillock formation in the annealed interconnections was enhanced by the segregation of sulfur atoms. These sulfur atoms should have been introduced into the electroplated films during electroplating. Therefore, it is very important to control the micro texture, the residual stress and the concentration of sulfur in the electroplated copper thin film interconnections to assure the stable life, in other words, to eliminate their sudden brittle fracture and time-dependent degradation caused by the residual stress in the thin film interconnections.

Effect of High-Frequency and High-Density Current on Adhesive Strength of Copper Thin Film

Adhesion improvement of Cu-based substrate and epoxy molding compound interface by hierarchical structure preparation

Microstructural Modification of Metallic Thin Films Via High-Frequency Alternating Current Treatment at Room Temperature

Optimization of Effective Parameters for Improving Adhesion Strength of Copper Nanowire Surface Fastener

S0301-1-4 Effect of High-Density Electric Current Field on the Slip at the Tip of Fatigue Cracks

Improving Adhesion Strength and Thermal Conductivity of Nanowire Surface Fastener

Improvement of Adhesive Strength of Nanowire Surface Fastener by the Optimization of Diameter Ratio of Nanowires

Improvement of Thermal Conductivity of Electroplated Copper Thin-Film Interconnections by Controlling Their Micro Texture

Effect of High-Density Electric Current on the Microstructure and Fatigue Crack Initiation of Stainless Steel

Research progress of interfacial adhesion force of copper plating on Ajinomoto build-up films for chip substrates

Improvement of Thermal Conductivity of Electroplated Copper Interconnections by Controlling Their Crystallinity

A New Method to Obtain Cu Films with Lower Resistivity and Higher Interface Adhesion on Different Substrates

Improvement of the reliability of TSV interconnections by controlling the crystallinity of electroplated copper thin films

G031072 Effect of Surface-Activated Pre-Coating on Crack Propagation in Fatigue Crack Healing

J212025 Fabrication of Nanowire Surface Fastener on Flexible Substrate and Its Electrical and Mechanical Properties

Stress-Induced and Electro-Migration of Electroplated Copper Thin Film Interconnections Used for 3D Integration

Aminosilanization Nanoadhesive Layer for Nanoelectric Circuits with Porous Ultralow Dielectric Film

Microstructure Regulation and Fabrication of Epoxy-based Conductive Films with Excellent Electrical and Thermal Conductivity, Adhesion, Toughness, and Flexibility

Adhesion improvement of sputtered Cu films on flexible polymer substrates through the design of metal interlayers

High-Adhesion Ag Film with Enhanced Electromagnetic Shielding Performance via Post-Treatment of a Polydopamine Adhesive Layer