Abstract:The evolution of surface morphologies of films prepared by ion-based deposition techniques has been investigated by atomic force microscopy. Two deposition processes, filtered arc deposition (FAD) and ion-beam-assisted deposition, where low-energy (<100 eV) ion irradiation and high-energy (several tens of keV) ion-beam bombardment concurrent with film growth were involved, respectively, have been employed to prepare TiN and Al films. Comparative studies on the effect of energetic ions on the development of topography have been performed between the low-ion-energy regime and high-ion-energy regime. In addition, the relationship between topography and mechanical properties of thin films has been revealed, by involving thin films prepared by thermal evaporation deposition (TED), where almost all depositing particles are neutral. In the images of the TED TiN and Al films, a large number of porous and deep boundaries between columnar grains was observed, suggesting a very rough and loose surface. In contrast, the FAD films exhibited much denser surface morphologies, although still columnar. The root-mean-square roughness of the FAD films was less than 1 Å. Hardness test and optical parameter measurement indicated that the FAD films were much harder and, in the case of optical films, much more transparent than the TED films, which was considered to arise from the denser surface morphologies rather than crystallization of the films. The high density and super smoothness of the FAD films, and the resultant mechanical and optical properties superior to those of the TED films, were attributed to the enhancement of surface migration of the deposited adatoms in the FAD process, which could provide intensive low-energy ion irradiation during film growth. As for topography modification by high-energy ion-beam bombardment concurrent with film growth, in addition to the increase of surface diffusion due to elastic collision and thermal spikes, physical sputtering must be considered while explaining the development of the film topography. Both surface migration enhancement and sputtering played important roles in the case of high-energy heavy-ion-beam bombardment, under which condition surface morphology characterized by dense columns with larger dimension and deep clean boundaries was formed. However, under high-energy light-ion-beam bombardment, the sputtering was dominant, and the variation of sputtering coefficient with position on the surface of growing film led to the formation of cones.

A New Method to Obtain Cu Films with Lower Resistivity and Higher Interface Adhesion on Different Substrates

The Effect of CU Intermediate Layer Made by IBAD on the CU Surface Film of E-Gun Evaporation

Preparation of Cr Hard Coatings by Ion Beam Assisted Electron Beam Vapor Deposition on Ni and Cu Substrates

Study on interface behavior of Be/CuCrZr alloy by diffusion bonding

Effect of High-Frequency and High-Density Current on Adhesive Strength of Copper Thin Film

Wear Resist Films Grown by Ion Beam Assisted Deposition in Gravure Printing

Metal vapor vacuum-arc ion implantation effects on the adhesion and hardness of ion-beam deposited Cr/Cu films

Properties of Cu Film and Ti/Cu Film on Polyimide Prepared by Ion Beam Techniques

Internal Stress and Adhesion of Cu Film/Si Prepared by Both Mevva and Ibad

Diffusion and Adhesion Properties of Cu Films on Polyimide Substrates

Nucleation and growth of low resistivity copper thin films on polyimide substrates by low-temperature atomic layer deposition

Ion Beam Assisted Thin Film Deposition

Cu Films by Partially Ionized Beam Deposition for Ultra Large Scale Integration Metallization

Improvement of interfacial adhesion strength and thermal stability of cu/cap barrier/low-k dielectric stack by plasma treatment on the surface of Cu film

Microstructural Modification of Metallic Thin Films Via High-Frequency Alternating Current Treatment at Room Temperature

Improved Electrical Resistivity of Atomic-Layer-Deposited Copper Thin Films on Polyimide Substrates by an In Situ ZnO Interlayer

Atomic Force Microscopy Study on Topography of Films Produced by Ion-Based Techniques

Enhanced adhesion strength between electroplated Cu and ABF substrate with isothermal annealing treatment

Surface Roughness Analysis of Cu Films Deposited on Si Substrates: A Molecular Dynamic Analysis

Adhesion improvement of sputtered Cu films on flexible polymer substrates through the design of metal interlayers

Interfacial Characterization of Low-Temperature Cu-to-Cu Direct Bonding with Chemical Mechanical Planarized Nanotwinned Cu Films