Abstract:During the fabrication of an indium-gallium-zinc oxide (IGZO) thin film transistor (TFT), the thermal process was used to reduce the resistivity of IGZO. The annealing temperature was found to have great influence on the transistor characteristics. At an optimized heat-treatment temperature, the depletion-mode IGZO TFT was fabricated with steeper subthreshold slope, higher filed-effect mobility and acceptable turn-on voltage. And the relatively conductive IGZO could directly replace the indium tin oxide as the transparent electrode of the organic light-emitting diode (OLED), reducing the mask count of the backplane for the active-matrix OLED display. INTRODUCTION Thin film transistor (TFT) based on metal oxide (MO), especially, indium-gallium-zinc oxide (IGZO), is considered as a good candidate to fabricate large area backplane for active-matrix organic light-emitting diode (AMOLED) display, due to its high mobility, good uniformity and low off-state current [1]. Our previous study [2] suggested that the resistivity (ρ) of IGZO highly depended on the heat-treatment conditions, such as annealing ambience, temperature, duration and gas permeability of IGZO cover, while the thermal process was often inevitable during the fabrication of IGZO TFT. With the active layer of IGZO covered with the gas-permeable silicon oxide (SiOx), the TFT was subjected to a serious anneals in an oxygen-deficient nitrogen (N2) ambience. With the increasing temperature, although the mobility was enhanced, the turn-on voltage (Von) became more and more negative. At an optimized temperature, the depletion-mode (DM) IGZO TFT with steeper subthreshold slope, higher filed-effect mobility and acceptable turn-on voltage was fabricated. Furthermore, such annealing-induced conductive IGZO source/drain regions can be directly used to replace the indium tin oxide (ITO) as the transparent electrode of OLED, reducing the mask count of AMOLED backplane. Annealing-Induced DM IGZO TFT Shown in Figure 1 is the evolution of the schematic cross-section of an IGZO TFT. A gate dielectric of 100 nm silicon oxide (SiOx) was first thermally grown on an n+ silicon substrate, which served as the gate electrode. 10 or 20 nm IGZO film was then room-temperature sputtered using a target of In2O3:Ga2O3:ZnO = 1:1:1 mol% in an atmosphere of 10% oxygen (O2) and 90% argon (Ar). After the patterning of the active-island using the hydrofluoric acid, a passivation layer of 300 nm SiOx was deposited at 300 oC in a plasma-enhanced chemical vapor deposition (PECVD) reactor. The tetraethylorthosilicate (TEOS) and O2 were used as the source gases. The contact holes were then opened and the resulting structure was subjected to a series of anneals, as shown in Figure 1a. Finally, 300 nm aluminum (Al) was deposited and patterned into electrodes (Fig. 1b). These TFTs were measured using an Agilent 4156C semiconductor parameter analyzer. n+ Si 100nm SiOx 300nm SiOx

P-1.13: Influence of the Source/Drain Material on Oxide Semiconductor Thin Film Transistors

Effects of Source/Drain Electrodes on the Performance of InSnO Thin-Film Transistors

Effect of Source/ Drain Electrode Fabrication Technology on the Electrical Properties of Solution-processed A-IGZO Based Transistors

Effect of Source/Drain Electrodes on the Electrical Properties of Silicon–Tin Oxide Thin-Film Transistors

Annealing-Induced Depletion-Mode Indium-Gallium-Zinc Oxide Thin-Film Transistor and Its Application to Active-Matrix Organic Light-Emitting Diode Display

Indium–gallium–zinc–oxide thin-film transistors: Materials, devices, and applications

Indium–gallium–zinc–oxide Thin-Film Transistors:Materials,devices, and Applications

Impact of electrode materials on the performance of amorphous IGZO thin-film transistors

High Performance Indium‐Gallium‐Zinc Oxide Thin Film Transistor via Interface Engineering

Amorphous NdIZO Thin Film Transistors with Contact-Resistance-Adjustable Cu S/D Electrodes

High Reliability Tungsten-Doped Indium Zinc Oxide Thin Film Transistors for Display Applications

Influence of indium doping on electrical performance of gallium oxide thin-film transistors

Properties of Al-doped ZnO film transistors with different source and drain electrodes

Titanium doped Zinc-oxide based Thin Film Transistors: Optimization of the source/drain materials

High-performance fully transparent Ti-Zn-O thin film transistors

Characteristics of Elevated-Metal Metal-Oxide Thin-Film Transistors Based on Indium-Tin-Zinc Oxide

Fabrication and Properties of InGaZnO Thin-Film Transistors Based on a Sol–Gel Method with Different Electrode Patterns

High-performance IGZO-based TFTs with Stacked Al<sub>2</sub>O<sub>3</sub>/HfO<sub>2</sub> Dielectrics

A study on the high mobility and improved reliability of Pr-doped indium zinc oxide thin film transistors

Thin Film Transistor Using Amorphous InGaZnO Films as Both Channel and Source/Drain Electrodes

High-Performance Indium-Gallium-Zinc-Oxide Thin-Film Transistors with Stacked Al<sub>2</sub>O<sub>3</sub>/HfO<sub>2</sub> Dielectrics