Abstract:During the fabrication of an indium-gallium-zinc oxide (IGZO) thin film transistor (TFT), the thermal process was used to reduce the resistivity of IGZO. The annealing temperature was found to have great influence on the transistor characteristics. At an optimized heat-treatment temperature, the depletion-mode IGZO TFT was fabricated with steeper subthreshold slope, higher filed-effect mobility and acceptable turn-on voltage. And the relatively conductive IGZO could directly replace the indium tin oxide as the transparent electrode of the organic light-emitting diode (OLED), reducing the mask count of the backplane for the active-matrix OLED display. INTRODUCTION Thin film transistor (TFT) based on metal oxide (MO), especially, indium-gallium-zinc oxide (IGZO), is considered as a good candidate to fabricate large area backplane for active-matrix organic light-emitting diode (AMOLED) display, due to its high mobility, good uniformity and low off-state current [1]. Our previous study [2] suggested that the resistivity (ρ) of IGZO highly depended on the heat-treatment conditions, such as annealing ambience, temperature, duration and gas permeability of IGZO cover, while the thermal process was often inevitable during the fabrication of IGZO TFT. With the active layer of IGZO covered with the gas-permeable silicon oxide (SiOx), the TFT was subjected to a serious anneals in an oxygen-deficient nitrogen (N2) ambience. With the increasing temperature, although the mobility was enhanced, the turn-on voltage (Von) became more and more negative. At an optimized temperature, the depletion-mode (DM) IGZO TFT with steeper subthreshold slope, higher filed-effect mobility and acceptable turn-on voltage was fabricated. Furthermore, such annealing-induced conductive IGZO source/drain regions can be directly used to replace the indium tin oxide (ITO) as the transparent electrode of OLED, reducing the mask count of AMOLED backplane. Annealing-Induced DM IGZO TFT Shown in Figure 1 is the evolution of the schematic cross-section of an IGZO TFT. A gate dielectric of 100 nm silicon oxide (SiOx) was first thermally grown on an n+ silicon substrate, which served as the gate electrode. 10 or 20 nm IGZO film was then room-temperature sputtered using a target of In2O3:Ga2O3:ZnO = 1:1:1 mol% in an atmosphere of 10% oxygen (O2) and 90% argon (Ar). After the patterning of the active-island using the hydrofluoric acid, a passivation layer of 300 nm SiOx was deposited at 300 oC in a plasma-enhanced chemical vapor deposition (PECVD) reactor. The tetraethylorthosilicate (TEOS) and O2 were used as the source gases. The contact holes were then opened and the resulting structure was subjected to a series of anneals, as shown in Figure 1a. Finally, 300 nm aluminum (Al) was deposited and patterned into electrodes (Fig. 1b). These TFTs were measured using an Agilent 4156C semiconductor parameter analyzer. n+ Si 100nm SiOx 300nm SiOx

Characteristics of Elevated-Metal Metal-Oxide Thin-Film Transistors Based on Indium-Tin-Zinc Oxide

Elevated-Metal Metal-Oxide (EMMO) Thin-Film Transistor: Technology and Characteristics

Indium–gallium–zinc–oxide thin-film transistors: Materials, devices, and applications

Indium–gallium–zinc–oxide Thin-Film Transistors:Materials,devices, and Applications

Annealing-Induced Depletion-Mode Indium-Gallium-Zinc Oxide Thin-Film Transistor and Its Application to Active-Matrix Organic Light-Emitting Diode Display

Enhancing the Stability and Mobility of TFTs via Indium-Tungsten Oxide and Zinc Oxide Engineered Heterojunction Channels Annealed in Oxygen Ambient

High Performance Indium‐Gallium‐Zinc Oxide Thin Film Transistor via Interface Engineering

P‐15: the Use of Fluorination to Enhance the Performance and the Reliability of Elevated‐Metal Metal‐Oxide Thin‐Film Transistors

A Bottom-Gate Indium-Gallium-Zinc Oxide Thin-Film Transistor With an Inherent Etch-Stop and Annealing-Induced Source and Drain Regions

High-Performance Amorphous InGaZnO Thin-Film Transistor Gated by HfAlOₓ Dielectric with Ultralow Subthreshold Swing

High-Performance Indium-Gallium-Zinc-Oxide Thin-Film Transistors with Stacked Al<sub>2</sub>O<sub>3</sub>/HfO<sub>2</sub> Dielectrics

Performance Enhancement of Indium Zinc Oxide Thin-Film Transistors Through Process Optimizations

P‐1.4: Elevated‐Metal Metal‐Oxide Thin‐Film Transistor with Fluorinated Indium‐Gallium‐Zinc Oxide Channel Towards Flexible Applications

High Performance and Hysteresis-Free a-IGZO Thin Film Transistors Based on Spin-coated Hafnium Oxide Gate Dielectrics

High-Performance Amorphous InGaZnO Thin Film Transistor With High-k Van Der Waals Molecular Dielectric

Impact of cation compositions on the performance of thin-film transistors with amorphous indium gallium zinc oxide grown through atomic layer deposition

Performance of Transparent Indium–Gallium–Zinc Oxide Thin Film Transistor Prepared by All Plasma Enhanced Atomic Layer Deposition

High mobility of IGO/IGZO double-channel thin-film transistors by atomic layer deposition

Room-Temperature-Processed Flexible Amorphous InGaZnO Thin Film Transistor.

Top-Gate Amorphous Indium-Gallium-Zinc-OxideThin-Film Transistors With Magnesium Metallized Source/Drain Regions

Performance Improvement of In-Ga-Zn Oxide Thin-Film Transistors by Excimer Laser Annealing