Abstract:The content of Zn and Mg directly influences the microstructure characteristics of Al–Zn–Mg–Cu alloys. In the present study, the solidification phases of three as-cast Al–Zn–Mg–Cu alloys with different Zn/Mg ratio (1.5, 1.8 and 2.1 at.%, successively) were thoroughly investigated, and their evolutions during homogenizations were analyzed with the aid of optical microscopy (OM), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and X-ray diffraction (XRD). The results showed that serious dendritic segregation existed in the as-cast microstructures. In the as-cast alloys with three different Zn/Mg ratio, the secondary phases are represented by non-equilibrium intermetallic phases (Mg(Zn,Cu,Al) 2 and Al 2 Cu) and precipitate MgZn 2 phase. Thereinto, the Mg(Zn,Cu,Al) 2 phase possessed a majority, which was determined through computational analysis of solidification processes. With the increase of Zn/Mg ratio, the amount of Mg(Zn,Cu,Al) 2 phase continuously decreased, while the content of Al 2 Cu phase showed only minor variation. As the Zn/Mg ratio increased, the strength and hardness of the as-cast alloy gradually improved. The Zn/Mg ratio has a significant impact on the dissolution and transformation of the secondary phases during homogenization process. As the Zn/Mg ratio increased, the melting point of the as-cast eutectic gradually decreased. Additionally, due to the higher diffusion rate of Zn compared to Mg and Cu elements, the dissolution rate of the secondary phase increased accordingly. At relatively low temperatures (380, 410, and 440 °C), phase transformation from the Mg(Zn,Cu,Al) 2 phase to the Al 2 CuMg phase occurred in all three alloys. However, phase transformation was only present in Low/Mid-Zn/Mg ratio alloys at 470 °C. These differences are attributed to the varying diffusion rates of Zn, Mg, and Cu elements during the homogenization process. The implementation of a two-stage homogenization process effectively addresses the issue of residual Al 2 CuMg phase in Low/Mid-Zn/Mg ratio alloys.

Effect of Two-Stage Homogenization Heat Treatment on Microstructure and Mechanical Properties of AA2060 Alloy

Microstructural Evolution and Kinetics of 7075 Al Alloy During Homogenization Treatment

Effect of homogenization temperature on microstructural homogeneity and mechanical properties of twin-roll casted 8006 aluminum alloy

Effects of Homogenization Treatment on the Microstructure and Mechanical Properties of Mg–8Li–3Al–Y Alloy

Microstructural Characterization of the As-Cast and Homogenized Al-Cu-Mg-Ag Alloy

Homogenization heat treatment influence on microstructure evolution and mechanical properties of as-cast Al-Li-Cu-Mg-Zr alloy for lightweight aerospace application

Isothermal Investigation and Deformation Behavior during Homogenization of 6063 Aluminum Alloy

Study on Precipitation in (cocrfemnni)90al6ti4 High Entropy Alloy

The Effect of Heat Treatments on the Microstructural Evolution of Twin-Roll-Cast Al-Fe-Si Alloys

Effect of Initial Microstructure on the Hot Deformation Behavior and Microstructure Evolution of Aluminum Alloy AA2060

The Effect of the Homogenization Treatment with an Electric Field on Second Phase Precipitation of 2091 Al-Li Alloy During Ageing Treatment

Influence of Homogenization Heat Treatment and Cooling Modes on Microstructure of AA7475 Aluminum Alloy Ingot

Tailoring intermetallic phase and mechanical property improvement in a novel Al-Zn-Mg-Cu-Y alloy via homogenization treatment

Influence of enhanced Li content on the as-cast eutectic phase features and the evolution during homogenization of Al-Cu-Li alloys

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Research on Homogenization Treatment of Mg-8wt.% Sn-1.5 Wt.% Al Alloy

Effects of homogenization on the microstructural evolution of a novel Zr and Er containing Al–Mg–Zn alloy

Effect of heat treatments on microstructure and mechanical properties of sand cast Al–2Li–2Cu–0.5Mg–0.2Sc–0.2Zr alloy

Effect of Zn/Mg ratio on the microstructure and mechanical properties of as-cast Al–Zn–Mg–Cu alloys and the phase transformation during homogenization

Homogenization heat treatment of Mg-9.0Y-3.0MM-0.6Zr alloy

Homogenization heat treatment of GWN751K magnesium alloy