Abstract:Dislocation loops in quenched aluminum alloys are usually seen deviating from their nominal habit planes, while the orientation distribution and deviation mechanism are far from understanding. Based on the method of tomographic crystallography of dislocations and correlative in-situ heating experiments in transmission electron microscopy (TEM), we revisit the three-dimensional (3D) characteristics and deviation behaviors of dislocation loops in a quenched Al-Cu alloy with an aim to fully unravel the relationship between dislocation crystallography and deviation behaviors. The results show that all the dislocation loops exhibit approximately circular shapes and have a/2 < 110>-type Burgers vectors, with loop orientations deviating from their pure edge orientation {110} of 0°-17.8° and distributing mainly close to the [101]-[001] and [101]-[111] edges of the standard stereographic triangle. Three types of deviation behaviors of dislocation loops are then defined, which are characterized by loop rotation around 〈100〉, 〈110〉 and irregular axes, respectively. Theoretical calculations of strain energy variation with increasing deviation angle indicate that the relatively low energy barrier may account for a high frequency of loop deviation in the low angle range. Detailed in-situ TEM heating experiments and correlative tomographic crystallography analyses strongly demonstrate the specific roles of dislocation gliding and climbing at elevated temperatures in the shrinkage, polygonization and deviation processes of dislocation loops, and the competitive and cooperative motion of dislocation segments close to slip planes {111} are the fundamental reasons for the formation of three types of deviated dislocation loops.

Electron Tomography of Dislocations in an Al-Cu-Mg Alloy

Orientation distribution and deviation behaviors of dislocation loops in a quenched Al-Cu alloy

Transmission Electron Microscopy Observation of a Dislocation Loop in an Al70Co15Ni15decagonal Quasicrystal

Dislocation Electron Tomography of Boundaries in Deformed Aluminium

Dislocations Observed by Transmission Electron-Microscopy in the Quasi-Crystalline Phase T2 of Al-Li-Cu after Deformation

Transmission Electron-Microscopy Study of Small-Angle Grain-Boundaries, Dislocations and Modulated Phases in Al-Li-Cu Quasi-Crystals

Experimental Characterization of Dislocations in Deformation Induced Planar Boundaries of Rolled Aluminium

Electron microscopy of a low stacking fault energy alloy

Transmission Electron Microscopy Study of the Microstructure and Dislocation Configuration in Al67Co8Ti25

Atomistic Study of Fundamental Character and Motion of Dislocations in Intermetallic Al2Cu

Direct observations of collinear dislocation interaction in a Fe-17.4 Mn-1.50 Al-0.29 C (wt.%) austenitic steel under cyclic loading by in-situ electron channelling contrast imaging and cross-correlation electron backscatter diffraction

On the Determination of Burgers Vectors of Type-B Dislocations in an Al70co15ni15 Decagonal Quasi-Crystal by Convergent-Beam Electron-Diffraction

Transmission Electron-Microscopy Analysis of Planar and Line Defects in an Al-Li-Cu Icosahedral Quasi-Crystal

STEM Characterization of Dislocation Loops in Irradiated FCC Alloys

Dislocation Network on the Curved End Face of Α Precipitates in a Ti-8 Wt.% Fe Alloy

In-situ TEM Characterization of Dislocation Loops in Tungsten under Simultaneous Helium and Hydrogen Irradiation

Dislocation content of geometrically necessary boundaries aligned with slip planes in rolled aluminium

Atomic Scale and 3D Characterization of the Heterogeneously Formed S (al2cumg) Precipitates at Dislocations in Al-Cu-Mg Alloy

Atomistic Simulations for the Evolution of a U-shaped Dislocation in Fcc Al

Insights into Electron Wind Force by a Helical Dislocation Reconfiguration

Molecular dynamics study on the Burgers vector transition of nanometric dislocation loops induced by cascade in bcc-iron