Abstract:Hypereutectic Al-Si alloys are used as material for the engine block and cylinder liners in automobiles. Wear behaviour of hypereutectic Al-Si alloy system changes significantly with applied normal load in both mild wear and severe wear regime. Significant improvement in wear resistance can be obtained by exposing silicon particles through the chemical etching process. For Al-25% Si alloys, most studies are reported in mild and ultra-mild wear regime. In the present work, the wear of exposed silicon particles with varying load and speed in severe wear regime was investigated under the unidirectional sliding condition and bi-directional sliding condition using a pin-on-disk tribometer (POD) and a linear reciprocating tribometer (LRT), respectively. Rapidly solidified and T6 heat-treated Al-25Si alloy was polished and etched using 5% NaOH solution to expose the silicon particles. Experiments were carried out with normal loads varying from 40 N to 120 N in dry sliding conditions. Sliding speeds of 0.8 m/s and 1.5 m/s were applied for each load in case of a pin on disk tribometer whereas, in an LRT, the sliding velocities were 0.2 m/s and 0.45 m/s respectively for each set of the load. The surface topography was measured by means of a 3-D optical profilometer, and surface morphology was analyzed using SEM images. It was observed that at higher loads, larger Si particles were fractured and pushed into the matrix. Fractured silicon particles, along with smaller particles, were embedded into the matrix, thereby increasing the silicon concentration in the wear region. The comparison of the experimental results of unidirectional and bi-directional sliding that reveal the change in surface morphology of silicon particles, the friction characteristics at the interface, variation of surface 3-D roughness parameters, the wear rate and wear mechanisms of Al-25% Si alloys are analyzed and reported in the study.

Dry Sliding Wear Properties of Rheo-diecasting Hypereutectic Al-Si Alloy with High Iron Content

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Contributions of the Particulate Reinforcement to Dry Sliding Wear Resistance of Rapidly Solidified Al-Ti Alloys

Dry sliding wear of MA/PM Al-10Ti alloy

Study on Microstructure, Mechanical Properties and Erosion Characteristics of Al-Si Alloy Manufactured by Continuous Casting Direct Rolling Process

Towards high performance Al–Si–Fe alloy castings via rheo-diecasting: Effect of injection velocity and heat treatment on microstructure evolution and property

A Comparison of the Sliding Wear Behavior of a Hypereutectic Al–Si Alloy Prepared by Spray-Deposition and Conventional Casting Methods

Dry sliding wear of PM Al-10Ti alloy

Enhanced comprehensive performance via alloying and rheo-diecasting in a semi-solid Al–Si–Fe–Mg–Cu–Sr alloy

Dry sliding wear of microalloyed Er-containing Al–10Sn–4Si–1Cu alloy

Tribological behavior of an AlCoCrFeNi2.1 eutectic high entropy alloy sliding against different counterfaces

Influence of Rheo-Diecasting Processing Parameters on Microstructure and Mechanical Properties of Hypereutectic Al–30%Si Alloy

Effects of second phase on dry sliding wear of rapidly solidified Al-Ti alloy

Tribological behaviour of hypereutectic Al-Si automotive cylinder liner material under dry sliding wear condition in severe wear regime

Friction and wear behavior of CuFe3Al powder metallurgical composites in dry sliding

Solidification behavior and enhanced properties of semi-solid Al–8Si–0.5Fe alloys fabricated by rheo-diecasting

Effect of Si Content on the Dry Sliding Wear Properties of Spray-Deposited Al–Si Alloy

Effects of silicon content and test conditions on the dry wear behaviour of Zn–30Al–3Cu–(0–5)Si Alloys

Dry sliding wear behavior of additively manufactured CoCrWNixAly alloys

Achieving low wear in a μ-phase reinforced high-entropy alloy and associated subsurface microstructure evolution